jetor water from a fixed nozzle has a diameter d of 30 mm and strikes a flat plate at angle u of 30° to the normal to the plate. The velocity of the jet v is 5m/s, and the surface of the plate can be assumed to be frictionless. Calculate the force exerted normal to the plate if the plate is moving with velocity u of 4m/s in the same direction as the jet. M=518 30% U1

jetor water from a fixed nozzle has a diameter d of 30 mm and strikes a flat plate at angle u of 30° to the normal to the plate. The velocity of the jet v is 5m/s, and the surface of the plate can be assumed to be frictionless. Calculate the force exerted normal to the plate if the plate is moving with velocity u of 4m/s in the same direction as the jet. M=518 30% U1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
A circular deep dish has a sharp-edged hole in its center. A jet of water speed V, hit the plate concentrically. Get an expression for external strength necessary to hold the dish in place, if the jet emitted from the hole also has speed V. Evaluate the force for V=5 m/s, D= 100 mm and d = 20 mm.
A 3-in-diameter horizontal water jet having a velocity of 90 ft/s strikes a curved plate, which deflects the water 180° at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream.
A 75 mm-diameter jet has a velocity of 33.5 m/s. It strikes a blade moving in the same direction at 21.3 m/s. The deflection angle is 150°. Assuming no friction, determine the final absolute velocity V2 of the water leaving the blade.
Assuming that the fluid enters to the pump with no shock / no swirl, construct the velocity triangles at both inner and outer diameters of the impeller for the case where the blade angle at the outlet is: β2 = 90o, and β2 = 130o
Water enters vertically and steadily at a rate of 60 L/s into the sprinkler shown, with unequal arms and unequal discharge areas. The smaller jet has a discharge area of 3 cm2 and a normal distance of 50 cm from the axis of rotation. The larger jet has a discharge area of 5 cm2 and a normal distance of 35 cm from the axis of rotation. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating.
Water, issuing vertically from a nozzle having a diameter of 25 mm, flows out under a head of 30 m. If C = Cv = 0.98, determine at what constant height could the jet of water support a load of 200 N vertically from the nozzle tip?
A jet of water has a velocity of 20m/s and flows at 2kgs/s. The jet strikes a stationary flat plate. The normal direction to the plate is inclined at 30º to the jet.Determine the force on the plate in the direction of the jet.
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 30°
As shown in the figure, the water entering axially into a turbine wheel emerges at a velocity of V = 5 m / s among 20 blades with a thickness of 5 mm. Calculate the water velocity at the impeller inlet.
A circular balloon is being filled through the inlet, which has a cross-sectional area denoted as A1. The air enters the balloon with a velocity V1 and a density ρ1. If the balloon radius is denoted as R, and the densitywithin is taken as an average value ρavg, construct an expression for the time rate of change of mass withinthe balloon.
A uniform tube is used to siphon water from the large tank. If the pressure on the outside of the tube (the atmospheric pressure) is more than 20 kPa greater than the pressure within the tube, the tube will collapse. By using Bernoulli's equation, determine the minimum value of h allowed without the siphon collapsing. The density of water is 1000 kg/m3. Hint: Since the tube is uniform the flow speed in it is constant. The exiting flow from the tube is treated as free jet. 2 m V SARA 1 4 m