a piping system (C = 120) consists of 3050 m of 750-mm (AB), 2440 m of 600-mm (BC) and, from C to D, two 400-mm pipes in parallel, each 1830 m long, (a) For a flow of 0.394 m3/s from A to D, what is the lost head? (b) If a valve in one of the 400-mm pipes were closed, what change in lost head would occur for the same flow

a piping system (C = 120) consists of 3050 m of 750-mm (AB), 2440 m of 600-mm (BC) and, from C to D, two 400-mm pipes in parallel, each 1830 m long, (a) For a flow of 0.394 m3/s from A to D, what is the lost head? (b) If a valve in one of the 400-mm pipes were closed, what change in lost head would occur for the same flow

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

A 60-cm water pipe carries a flow of 0.1 m³/s. At point A the elevation is 50 meters and the pressure is 200 kPa. At point B, 1200 meters downstream from A, the elevation is 40 meters and the pressure is 230 kPa. The head loss , in feet, between A and B isA. 6.94B. 15.0C. 20.88D. 100.2
The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flow through the pipe, what must be the pressure at A?
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B.
For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the head loss from A to B in terms of Q. a. 0.056Q2 b. 0.029Q2 c. 0.016Q2 d. 0.096Q2 2. Assuming Q = 12 cfs, compute the head loss of pipe CD. a. 15.78 ft b. 13.02 ft c. 18.56 ft d. 24.56 ft 3. Assuming Q = 12 cfs, compute the total head loss from A to D. a. 47.786 ft b. 56.673 ft c. 89.451 ft d. 32.562 ft
At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters head, the diameter is 7 meters, for a geometrical similar turbine to develop 36,000 HP under a 11 meters head. After resolving the percentage change in probable flow, determine the following: (A) What diameter, in meter, of the impeller to be used? (B) What is the speed, in RPM, should be used?
PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d’Eau) that is discharged 130 m straight upward (measured from the surface of the lake). The exit of the discharge pipe is 20 cm in diameter.
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.