A pump delivers heavy fuel oil at 60°F through 1000 ft of 2" brass pipe to a tank 10 ft higher than the supply tank. Neglecting minor losses, for a flow of 0.131 cfs determine the size of the pump (horsepower) if its efficiency is 80%. Water at 38°C flows from A to B through 244 m of average 300-mm-l.D. cast iron pipe (e = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3 /s is to flow through the pipe, what must be the pressure at 07

A pump delivers heavy fuel oil at 60°F through 1000 ft of 2" brass pipe to a tank 10 ft higher than the supply tank. Neglecting minor losses, for a flow of 0.131 cfs determine the size of the pump (horsepower) if its efficiency is 80%. Water at 38°C flows from A to B through 244 m of average 300-mm-l.D. cast iron pipe (e = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3 /s is to flow through the pipe, what must be the pressure at 07

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
10.) A horizontal pipe gradually reduces from 300 mm diameter section to 100 mm diameter section. The pressure at the 300 mm section is 100 kPa and at the 100 mm section is 70 kPa. If the flow rate is 15 liters/sec of water, compute the head lost between the two sections. Answer: 2.872m Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
Use figure below Question : Water at 20 C is to be pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, as shown in the figure. If the pipe is galvanized iron of diameter 7 in and the pump is 75% efficient, what horsepower pump is needed? Neglect minor losses. HINT : pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, & galvanized iron of diameter 7
An air-conditioning system is designed to have a ductwith a rectangular cross section 1 ft by 2 ft, as shown. Duringconstruction, a truck driver backed into the duct and made it atrapezoidal section, as shown. The contractor, behind schedule,installed it anyway. For the same pressure drop along the pipe,what will be the ratio of the velocity in the trapezoidal duct tothat in the rectangular duct? Assume the Darcy-Weisbach resistance coefficient is the same for both ducts.
10. What hose I.D. would be required to deliver 50 gal/min , assuming no friction losses at a maximum velocity of 8.5 ft/sec?
With the given pipe lengths, sizes and connections and if all pipes have an f=0.020. 1. which of the following most nearly gives the flow in pipe 2? a. 7 cfs b. 6 cfs c. 5 cfs d. 11 cfs 2. which of the following most nearly gives the head loss between B and C? a. 60 ft b. 100 ft c. 40 ft d. 80 ft with solution pls
A 2-inch diameter hose is conveying water at a flow rate of 20 gpm from point A to point B. The pressure at point A is 40 psi. The elevation at point A is 20 ft above mean sea level (MSL) and the elevation at point B is 18.5 ft above MSL. The hose is 100 ft long. Determine (a) pressure at point B if there is no head loss, (b) pressure at point B if head loss is 1 inch per foot of pipe length. (c) Compare pressure at B with and without headloss - what impact does head loss have?
4) A pump operates at 2000 rpm and delivers 200 gal/min at 90 ft head. The water distribution operator is requested to increase the head and flow in the network due to a leak. He increased the pump speed to 2160 rpm. What are the corresponding head and discharge?
How many gal/hr of water at 68 deg F can be delivered through a 1320-ft length of smooth 6.00 in i.d. pipe under a pressure difference of 0.25 psi. Assume that the pipe is “hydraulically smooth”
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above