A piston cylinder assembly contains water. Heat is transferred to the cylinder in order to heat the water. The atmospheric pressure is equal to 100 kPa. Determine the boiling temperature of water if the mass of the piston is equal to 1000 g. Consider g= 10 m/s^2. The cross sectional area of the piston is equal to 100 cm^2. Select one: О а. 102.3 С O b. 97.92 C О с. 103.4 с O d. 99.9 C

A piston cylinder assembly contains water. Heat is transferred to the cylinder in order to heat the water. The atmospheric pressure is equal to 100 kPa. Determine the boiling temperature of water if the mass of the piston is equal to 1000 g. Consider g= 10 m/s^2. The cross sectional area of the piston is equal to 100 cm^2. Select one: О а. 102.3 С O b. 97.92 C О с. 103.4 с O d. 99.9 C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.51 m and is kept at 111 deg C. What is the power required to boil the water? Tsat = 100°C; Properties of water at 100°C: Density, ρl= 961 kg/m3; Kinematic viscosity, ν = 0.293x10-6 m2/s; Prandtl Number, Pr = 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, μ = ρ × ν = 961 × 0.293 × 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 kJ/kg; ρv = 0.597 kg/m3; σ = 0.0588 N/m; Csf=0.013; n=1; Select one: a. 25964.0356 b. 52997.1101 c. 49373.4011 d. 38911.7986
When does boiling occur in a fluid? Briefly state Pascal's Law?
Explain the Variation of the standard atmospheric pressure and the boiling (saturation) temperature of water with altitude
A new temperature scale, °W is desired with freezing of water at 24°W and boiling point atatmospheric at 940°W. Determine the equivalent of 110°F in °W.
(About measuring specific heat capacity) Since metal sample can be heated to any desired temperature value, say, 65°C or 156°C. Why is it practical to set the initial temperature of the metal sample near the boiling point of water? In connection to this, why should the dipper be partly submerged in the water while heating the metal sample?
In a reservoir system with a very large accumulation volume for the ideal fluid (water),a) Since the diameter of the ABCDEF outlet pipe is D = 20 cm, the flow rate through the pipe,b) Calculate the velocity, velocity height, relative pressure and pressure heights in the ABCDEF outlet pipe.c) Draw the relative energy and piezometer lines of the system.d) If the relative evaporation pressure of water is pv = -98.5 kPa, what can be z maximum?e) Determine how much the diameter of the outlet pipe can be reduced at most without causing cavitation, with the relative evaporation pressure of water pv = -98.5 Pa and h = 6 m.f) Calculate the critical velocity value for cavitation.
The boiling temperature of water decreases by about 3°C for each 1000-m rise in altitude. What is the decrease in the boiling temperature in (a) K, (b) °F, and (c) R for each 1000-m rise in altitude?
Henry's constant for air at 25 C is ____orders of magnitude higher than hydrogen sulfide
Scale and sludge formation causes serious problems in boilers. Explain how the scalesand sludge are formed in the boilers and the problems caused by them. How can theseproblems be avoided?
6. A vertica platc 450 mm high and maintained at 3°C is exposed o satuated seam atatmospheric pressare. Calculte: (1) The rate of hea ransfe, and () The condensate a per hour per mete for plae widih film condensation. “The propertiesof waer im at the mean temperaure are: 0.3 kg/m sk = 6.4 x 10 WinC; = 434 x 10° kg/ms; and b = 22569 kg [Ans. 4399 x 10° kI, 2188 ke/h]
A new temperature scale in ºE is proposed wherein the boiling and freezing temperatures of water are1250 ºE and 85 ºE respectively. If a fluid system has a temperature of 525 ºE, determine its temperaturein a) ºC and b) ºR.