A plastic beam has a cross section with dimensions of a = 1.0 in., b = 3.5 in., d = 2 in., and t = 0.3 in. The centroid is located c = 0.846 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is l, = 1.283 in. 4. For a shear force of V = 3700 lb, what is the maximum shear stress in the beam? %3D %3D y t (typ.) d V b

A plastic beam has a cross section with dimensions of a = 1.0 in., b = 3.5 in., d = 2 in., and t = 0.3 in. The centroid is located c = 0.846 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is l, = 1.283 in. 4. For a shear force of V = 3700 lb, what is the maximum shear stress in the beam? %3D %3D y t (typ.) d V b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.
vertical bar is loaded with axial loadsat points B, C, and D, as shown in the figure. Thebar is made of steel with a modulus of elasticityE = 29,000 ksi. The bar has a cross-sectional area of8.24 in2. Calculate the displacements at points B, C,and D. Ignore the weight of the bar.
A 10 m long beam has 2 supports at point A and B. The beam is pinned at Support A and supported by a roller at Support B. It is carrying a car at middle of the beam. Discuss the results and explain the stress of this beam. Provide your opinion on the effect of the beam when the centroid of the vehicle is shifted to 3m away from Support B. Mass of car is given 1660kg. Please calculate shear force and moments for 0 ≤ X ≤ 5m and 5 < X ≤ 10m in first case and also for 0 ≤ X ≤ 7m 7 ≤ X ≤ 10m when the vehicle is shifted to 3m away from Support B. Using equilibrium i.e. force and moment equilibrium must be sa tisfied for each component, determine the forces or/and moments. List all assumptions that are Draw the free-body diagrams for the Draw the shear force and bending moment diagrams for each
A plastic beam has a cross section with dimensions of a = 3.8 in., b = 13.3 in., d = 7.6 in., and t = 1 in. The centroid is located c = 3.214 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is Iz = 247.59 in. 4. For a shear force of V = 1750 lb, what is the maximum shear stress in the beam?
Figure 1a shows a simply supported beam, AB of length L = 5.6 m, with a uniform distributed load of w = 4.5 kN/m. The shear force diagram is shown below the beam and the cross-section in Figure 1b. The cross section has a constant thickness t = 8.7 mm, the width of the flange is b = 217.5 mm and height of the web is d = 211.41 mm. 1. Determine the position of the neutral axis. 2. Determine the moment of inertia about the neutral axis
Block on a rough surface weighing 400 N Angle of internal friction is 21.8⁰. Solve for the force P required to impend motion if the force is applied to block horizontally.
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
2. Block B has a mass, mb, and is supported as shown. What is the maximum value of mb that can be lifted under force P = 300 lb applied to block A as shown? The static coefficient of friction on all surfaces is 0.2.
Write the stiffness matrix corresponding to the degrees of freedom 1, 2, and 3 of the continuous beam shown in Figure P16.2.