A simple and accurate viscometer can be made from a length of capillary tubing. If the flow rate and pressure drop are measured, and the tube geometry is known, the viscosity of Newtonian liquid can be computed. A test of a certain liquid in a capillary viscometer gave the following data: 3, Flow rate: 880 mm /s, Tube length: 1 m, Tube diameter: 0.50 mm, Pressure drop: 1.0 MPa

A simple and accurate viscometer can be made from a length of capillary tubing. If the flow rate and pressure drop are measured, and the tube geometry is known, the viscosity of Newtonian liquid can be computed. A test of a certain liquid in a capillary viscometer gave the following data: 3, Flow rate: 880 mm /s, Tube length: 1 m, Tube diameter: 0.50 mm, Pressure drop: 1.0 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
In a falling-ball viscometer, a steel ball 1.6 mm in diameter is allowed to fall freely in a heavy fuel oil having a specific gravity of 0.95. Steel weighs 79 kN/m3. If the ball is observed to fall 250 mm in 10.5 s, calculate the viscosity of the oil.
A liquid with a specific gravity of 4.7 and a viscosity of 1.3 cp flows through a smooth pipe of unknown diameter, resulting in a pressure drop of 0.183 lbf/in² for 1.73 mi. What is the pipe diameter in inches if the mass flowrate is 5,900 lb/hr?A. 3.64 inB. 0.44 inC. 5.74 inD. 0.005 in
C1 (a). A lubricating oil having the dynamic viscosity of 0.055 poise and kinematic viscosity of 0.17 stokes. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the specific gravity, and (iv) the specific volume in m3/kg. C1 (b). Calculate the capillary effect in mm in a glass tube of 4.4 mm diameter, when immersed in (1) water (2) mercury. The values of surface tension in contact with air are 0.0737 N/m and 0.54 N/m respectively. The contact angle for water =00 and mercury =1300. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) C1(a).(i).The density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the specific gravity C1(a). (iv) the specific volume in m3/kg C1 (b). 1.The capillary effect (water) in mm C1 (b). 2.The capillary effect (mercury) in mm
A study of the physical characteristic of honey was conducted due to thelarge demand of royal jelly. A capillary tube viscometer was used by aresearcher in determining the viscosity of the honey. The viscometer is250 mm long with an outside diameter of 55mm and effective thickness of2.5mm and was used horizontally so that the effect of gravity wasneglected. At an ambient temperature of 30oC the following data werecollected: ΔP (Pa) Q (cc/s)10.0 1.2512.5 1.5515 1.8017.5 2.0520.0 2.55 What will be the stress produced per unit length in the tube used in theproduction of royal jelly if it has a radius of 5mm and a flow of 1 capsuleper second. (1 capsule = 0.85 cc of royal jelly).
A Pipe used to transport an oil of specific gravity of 0.90 & 0.03poise at a Velocity of 1.6977m/s with a flow rate of 3cubic meter per second. A Pipe was used to conduct a test using water at 20 degree celsius with a velocity of 5.0931m/s. Find the diameter of the prototype. Viscosity of water at 20 degree celsius is 0.01poise
A2 A Newtonian fluid with viscosity (Mu) flows upward at a steady rate between two parallel plates that make an angle y with the horizontal. The fluid thickness h is much smaller than the width of the channel W. The pressures at each end, P(0) and P(L), are known and the pressure variations in the y-direction are small. Assume that Vy and Vz = 0 and Vx is a function of y alone. Use the shell balance to approach : - the Total flowrate, QV
A single-cylinder rotational viscometer is used to measurea liquid with viscosity of 100 cP using a spindle with 6 cmlength and 1 cm radius. At maximum shear rate (rpm560),the measurements approach a full-scale reading of 100.Determine the spindle dimensions that will allow theviscometer to measure viscosities up to 10,000 cP atmaximum shear rate. Answer is 1.293 cm
A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in throughnarrow gap of length, L as depicted in Figure 2. Following below values are given:c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm.The lubricant, of dynamic viscosity  = 1.0054 kg/m.s completelys fills the gap and the velocitydistribution is asssumed to linear as shown in Figure 2. The maximum allowable force in tape isgiven as F = 30.04 N. Find the maximum allowable tape speed
At low velocities (laminar flow), the volume flow Q through a small-bore tube is a function only of the tube radius R, the fluid viscosity ?܇, and the pressure drop per unit tube length dp/dx. Using the Buckingham pi theorem, find an appropriate dimensionless relationship. Make use of Table 1
One type of viscometer involves the use of a rotating cylinder inside a fixed cylinder as shown in the figure below. The gap between the cylinders must be very small to achieve a linear velocity distribution in the liquid. Design a viscometer that will be used to measure the viscosity of motor SAE 30 oil from 0°C to 100°C. Here you need to determine and report the following parameters: a. The dimensions of the two cylinders, lengths, thicknesses and diameters. b. The gap clearance between the surfaces of the cylinders. c. The rated power of the driving motor. d. The rotational speed of the shaft.
SAE 10W30 motor oil has a dynamic viscosity of 0.21 kilograms per meter second and a specific gravity of 0.896 (a) What is the density of the motor oil in units of kilograms per cubic meter?