A positive-feedback amplifier circuit (inverting Schmitt trigger) is shown in the following figure. In each of the situations below, determine output voltage given the applied trigger signal verigger, initia output vout and power supply rails +VcC, where Vcc = 15 V. The first three questions start the circuit in the positive stable state, the next three start the circuit in the negative stable state. 3 k2 2 k2 vt Vout O V Vtrigger

A positive-feedback amplifier circuit (inverting Schmitt trigger) is shown in the following figure. In each of the situations below, determine output voltage given the applied trigger signal verigger, initia output vout and power supply rails +VcC, where Vcc = 15 V. The first three questions start the circuit in the positive stable state, the next three start the circuit in the negative stable state. 3 k2 2 k2 vt Vout O V Vtrigger

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

2-) The AC equivalent of a feedback amplifier circuit is given in the figure on the right. (Hfe100, Va = ∞, Ic1 = 15 mA, Ic2 = 5mA and Ic3 = 5 mA) a) State the type of feedback used in the circuit, explaining the reason. b) Draw the small signal equivalent of the amplifier circuit. c) Calculate the value of β for the feedback by drawing the β circuit. d) Find the Avf = Vo / Vs closed loop gain of this circuit. e) Find the Rif and Rof values.
Use feedback theory to derive an expression for the input impedance of the “shunt-shunt” feedback amplifier as shown.
An inverting amplifier is to be designed with a gain of 5 and an input impedance of 10k ohms. What should be the value of the feedback resistance?
Discuss the difference between the current series negative feedback amplifier and voltage shunt feedback amplifier in terms of output impedance, input impedance, voltage gain, bandwidth, distortion and noise.
An amplifier has an open-loop gain of 92 dB, Rid = 75 kΩ, and Ro = 1400Ω. The amplifier is used in a feedback amplifier configuration with a resistive feedback network. (a) What is the largest value of current gain that can be achieved with this feedback amplifier? (b) What is the largest valuetransconductance that can be achieved with this feedback amplifier?
What is positive feedback and negative feedback with diagram?
Find the loop gain, current gain, input resistance, and output resistance for the shunt-series feedback ampliﬁer as shown if the 10-kΩ source resistor is eliminated from the ampliﬁer circuit.
A unity feedback system with open-loop transfer function given as:?(?) = ??. ?(? + ?)(? + ?)(? + ??)without affecting its operating point (−1.54 ∓ ??2.66) appreciably a- Design a suitable compensator to drive the step response error to zero.b- Design a suitable compensator to reduce step error by factor of 5.
(a) Calculate the sensitivity of the closed-loop input resistance of the series-shunt feedback ampliﬁer with respect to changes in open-loop gain A:SRinA = A/ Rin ∂Rin/ ∂A (b) Use this formula to estimate the percentage change in closed-loop input resistance if the openloop gain A changes by 10 percent for an ampliﬁer with A = 94 dB and β = 0.01. (c) Calculate the sensitivity of the closed-loop output resistance of the series-shunt feedback ampliﬁer with respect to changes in open-loop gain A:SRout A = A /Rout ∂Rout /∂A (d) Use this formula to estimate the percentage changeinclosed-loopoutputresistanceiftheopenloop gain A changes by 10 percent for an ampliﬁer with A =100 dB and β =0.01.
For the unity feedback system given below, the damping ratio of the closed looppoles is given by a) 1.5 b) 1 c) 0.5 d) 0.25
Ques 2: What is the Voltage series feedback? Explain the effect of feedback on gain and input, outputimpedance
Find the steady-state error as a function of time for the unity feedback system,..