(c) Analyze the circuit shown in Figure Q1(c). (i) Determine the type of negative feedback used in the circuit by showing the suitable process. (ii) Derive the equation for the feedback factor and the gain of the circuit. (ii) Calculate the feedback factor and the gain of the circuit if R1 = 1.2 kn, R2 = 15 kn and RĻ = 6.8 k2. R2 RI -Vo RL Vs Figure Q1(c)

(c) Analyze the circuit shown in Figure Q1(c). (i) Determine the type of negative feedback used in the circuit by showing the suitable process. (ii) Derive the equation for the feedback factor and the gain of the circuit. (ii) Calculate the feedback factor and the gain of the circuit if R1 = 1.2 kn, R2 = 15 kn and RĻ = 6.8 k2. R2 RI -Vo RL Vs Figure Q1(c)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

The open loop transfer function of unity feedback system is ??(??) = ??????????(??+??)(??+????).1- Assess the stability of the system.2- If the gain ?? is connected in series with G(s) as shown in figure Q1, Determine the range of ?? for stable system.
Analyze the circuit shown in Figure Shown.(i) Determine the type of negative feedback used in the circuit by showingthe suitable process. (ii) Derive the equation for the feedback factor and the gain of the circuit. (ii) Calculate the feedback factor and the gain of the circuit if R1 = 1.2 kΩ,R2 = 15 kΩ and RL = 6.8 kΩ.
Consider a unity negative feedback system with loop transfer function shown in Figure where L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1)L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1) Determine the value of K for which the closed-loop system is stable.
2-) The AC equivalent of a feedback amplifier circuit is given in the figure on the right. (Hfe100, Va = ∞, Ic1 = 15 mA, Ic2 = 5mA and Ic3 = 5 mA) a) State the type of feedback used in the circuit, explaining the reason. b) Draw the small signal equivalent of the amplifier circuit. c) Calculate the value of β for the feedback by drawing the β circuit. d) Find the Avf = Vo / Vs closed loop gain of this circuit. e) Find the Rif and Rof values.
3- Consider the unity feedback system shown below. a)Find the range of k for which the closed-loop system is table. b)What is the steady-state error for unit ramp and step inputs.
For the unity feedback system given below, the damping ratio of the closed looppoles is given by a) 1.5 b) 1 c) 0.5 d) 0.25
An amplifier has an open-loop gain of 92 dB, Rid = 75 kΩ, and Ro = 1400Ω. The amplifier is used in a feedback amplifier configuration with a resistive feedback network. (a) What is the largest value of current gain that can be achieved with this feedback amplifier? (b) What is the largest valuetransconductance that can be achieved with this feedback amplifier?
(a) Calculate the sensitivity of the closed-loop input resistance of the series-shunt feedback ampliﬁer with respect to changes in open-loop gain A:SRinA = A/ Rin ∂Rin/ ∂A (b) Use this formula to estimate the percentage change in closed-loop input resistance if the openloop gain A changes by 10 percent for an ampliﬁer with A = 94 dB and β = 0.01. (c) Calculate the sensitivity of the closed-loop output resistance of the series-shunt feedback ampliﬁer with respect to changes in open-loop gain A:SRout A = A /Rout ∂Rout /∂A (d) Use this formula to estimate the percentage changeinclosed-loopoutputresistanceiftheopenloop gain A changes by 10 percent for an ampliﬁer with A =100 dB and β =0.01.
A unity feedback system with open-loop transfer function given as:?(?) = ??. ?(? + ?)(? + ?)(? + ??)without affecting its operating point (−1.54 ∓ ??2.66) appreciably a- Design a suitable compensator to drive the step response error to zero.b- Design a suitable compensator to reduce step error by factor of 5.
For the system shown in Figure 3, first find the values of K1 and K2 to obtain a peak time of 1 second, and a settling time of 2 seconds, for the closed-loop step response of the system. Then find the poles of the closed-loop transfer function, T(s) = C(s)/R(s). Construct the corresponding graph of poles and zeros
An ampliﬁer has an open-loop voltage gain of 90 dB, Rid = 50 kΩ, and Ro = 5000 Ω. The ampliﬁer is used in a feedback conﬁguration with a resistive feedback network. (a) What is the largest current gain that can be achieved with this feedback ampliﬁer? (b) What is the largest transconductance that can be achieved with this feedback ampliﬁer?
For the system of Figure 2, ? = 2 s and?(?) =?(? + 0.8)(? − 1)(? − 0.6)Figure 2. Unity feedback system.a) Determine the range of ? for stability using the Routh–Hurwitz criterion.b) Determine the range of ? for stability using the Jury test. For more detailed question you can look at the image.