A pressure transducer has an ange and range of (4 to 20) mA. What is the ideal line for the above pres O a. 1 = 0.0016P + 4.5 O b.1 = 0.16P + 4.0 O c.I = 0.016P + 4.0 O d.I = 0.0016P + 4.0

Q: (ii) Figure Q.4(a) shows a basic comparator circuit with its transfer characteristie (V. vs V;).…

A: Comparator is an application of open loop opamp circuit . In open loop opamp if output voltage can…

Q: QI/ Assume the numerical values for the input voltage are Vin=50mV, and tl=ls.this input voltage is…

A: As per the guidelines of bartleyby I have to answer first question only.

Q: Calculate the range in the output voltage for the circuit shown below if the input voltage can vary…

A: We need to find out output voltage for given circuit

Q: Exercise 3. Find the current in R. Rp (partial answer: IR, =+3.00nA to the lett) and the output DC…

A: From the figure, write the voltage value at the non-inverting terminal of the op-amp. V+=0 V

Q: Quèstion 11 The current gain(a) is greater than the current gain(B). O True False

A:

Q: The stage gains in a superheterodyne are as follows: RF amplifier 10 d mixer 6 dB, two IF amplifiers…

A:

Q: 2. In an opamp inverting amplifier circuit, Rf = 10 kN. and Ri = 1.6 kN. Find the output voltage…

A:

Q: QUESTION 25 Find the value of Rf that will produce the closed loop gain of-236 R R VinoW o Vout 10 k

A:

Q: for question number 4 the final answer should be 8 or +-8 or 16 ?? A unipolar DAC is required to…

A: Given:- DAC The resolution must be =0.125 V The maximum Voltage must be=7.875 V

Q: In the circuit VREF = 2.5 V, and VIN = 1.5 V. The output voltage is p+Vcc Vo Hot Vout VN VREF +0…

A: First check diode conduction by open circuit method. The anode voltage is VA=V0 The cathode voltage…

Q: 7 O ca ku late R required to set Vcz 5V. Draw the Dcoblindicate the Q-point and what is operating…

A:

Q: Q5. Choose the correct answer ( with prove on the figure) The open loop of unity feedback system s^2…

A: G(S) = K(s2+2s+101)(s3+4s2+30s+52)poles s=-2 , -1±j5Zeros s=-1 ±j10No of poles P=3No of Zeros…

Q: The transducer, which depends on the effect of Seeback is, RTD Thermocouples LVDT Thermistor

A: Thermocouples are primarily based on the Seebeck effect: In an open circuit, consisting of two wires…

Q: The differentiator has Resistor =100k ohms, and Capacitor= 0.1uF. Given that vi=2cos(300t),…

A:

Q: • Common mode voltages: in this config the 2 voitages are identical The common-mode input voltage,…

A:

Q: 9. Figure 12–62 shows the output voltage of an op-amp in response to a step input. What is the slew…

A: We know direct formula for skew rate .

Q: Q2) design a wien bridge to produce an output sinusoid that can be adjusted from 400 Hz to 100 kHz…

A:

Q: D1.31 Use Mason's gain rule to find the transfer function of each system of Figure DI.31. RG) 1 R(s)…

A:

Q: In this circuit, one power amplifier A1=17 dB feeds into an attenuator circuit, which then feeds…

A:

Q: The output of an LVDT is connected to a 5 V voltmeter through an amplifier whose amplification…

A:

Q: A lead network shown in the figure is designed to compensate the drop in the gain for a biopotential…

A:

Q: the input is a.-sin (wt) b.none of the above c.sin

A:

Q: Design and draw  three-bits subtraction respectively using only Half Subtractor. Differentiate…

A: According to question, Design and draw  three-bits subtraction respectively using only Half…

Q: In a Cockroft-Walton circuit, input voltage 150 kV load current 5 mA,supply frequency 60 Hz, each…

A: For a Cockroft walton circuit, Input voltage=maximum voltage Vmax=150 KV=150×103 VLoad current I=5…

Q: a student is working on inverting amplifier having input voltage is 2.5 mv input resistance is 2…

A: As per our policy we can provide solution of first three question only. As we have given: Rf=200…

Q: Figure A.2 below and its transfer characteristic resPectively. A.1 and are the circuit oF Q) Frgure…

A:

Q: Assume Is = 8 x 10-16 A, B = 100, VT= 26mV and VA =00, For the circuit shown below and for lh= 3 mA,…

A: Transconductance is defined as it is the ratio of collector current to the thermal  voltage Vt gm =…

Q: 2. In an opamp inverting amplifier circuit, Rf = 10 kN. and Ri = 1.6 kN. Find the output voltage…

A: output voltage of inverting op amp is -RfRi× input voltage we will use above relation to find output…

Q: Q) In the Voltage Series feedback (a) Rof= Ro (1+Aß) and Rif = Ri / (1+AB) (b) Rof= Ro / (1+Aß) and…

A: In voltage series feedback  Input and output both are voltage The other name of voltage series…

Q: Q6.) Identify whether the following statement are true(T) or false (F) 4-A piezo-electrical…

A: Here we check whether the given statements are T or F.

Q: R Vn Vout 1. Find H(w) = Vo/Vi. 2. Derive an expression for the cutoff frequency. 3. Calculate the…

A:

Q: For feedback cct below, choose any value you want for the Rc resistor, then find 1. The feedback…

A: Given feedback circuit: Let's consider RC=0.025 kΩ To find: (a) The feedback topology (b) Avf, Aif,…

Q: 2- If capacitor =0.1 micro farad and feedback resistance=1.6 k ohm then Corner frequency =.......KHz…

A: Corner frequency (also known as Cut off frequency) is the frequency at which the frequency response…

Q: Design an analog circuit diagram to the following analog equation: Vo = 0.35V1-5.24V2-4.5

A:

Q: If Vin = 10 mV p-p what is the output voltage from the circuit shown below? + 20 V R, 2.2 kN Vin o…

A:

Q: The gain of the instrumentation amplifier IA is 800. Determine the gain of the circuit V. /VIN?…

A:

Q: In the figure shown, if the transconductance gm-1 mA/V, and Rs << Ro The Voltage gain Av is + Vno…

A: we have to find gain of common source amplifier with bypass capacitor Cs here trans conductance…

Q: Consider the Sallen key low pass circuit shown in Figure 2. Drive the transfer metion Vo (s)/V¼(s).…

A: In this question,  Drive the transfer function Vo(s) /Vi(s).  We are solved this problem using the…

Q: 1. What is circuit type 2. Find Vc, Vo 3. Drawing output voltage form f = 1000 Hz 10 C =0.1 µF 12 14…

A:

Q: Q2 Calculate the voltage gain, output voltage, input impedance, and output impedance for the cascade…

A: First we will do dc parameters to find signal parameters , then we will do ac analysis to find out…

Q: 2- If capacitor =0.1 micro farad and feedback resistance=1.6 k ohm then Corner frequency =.......KHz…

A: In this question,  We need to choose the correct options What is corner frequency?  .. Given all the…

Q: Q.No.3: 10 For a 4-bit weighted resistor digital to analog converter as shown in figure (a) with VR=…

A: Digital to analog convert.  4 bit weighted resistor with VR = 5V Determine the output voltage if…

Q: ampi feeds into än attenuator circuit, which then feeds into a seco power amplifier stage A2=33.2…

A:

Q: bü 4 A certain op-amp has an open-loop gain of 80,000. The maximum saturated output levels of this…

A:

Q: A boost converter has an input voltage Vb=5V. The average load current is lo=0.5A. The switching…

A: In this question , boost converter is given....We have to find out critical inductance and critical…

Q: the operating frequency of the transducer is modelled by : f(v)=50 tanh(@sv –),. ide fully explained…

A: Solution- 1.  Given,         f(v) = 50 tanh (ωsv-π8)           v  = 1v           ωs = 0.01 rad/sec…

Q: ermine the critical value of gain K for stability. Assume that the sampling period is 0.1 se ain K…

A:

Q: A certain differential amplifier has R, of 9.9 kn and R2 of 17kn. Vini =8.2mV and Vin=25.8mV Then…

A: For this problem we can easily found output voltage by applying nodal analysis at two input…

Q: Assume Is = 8 x 10-16 A, B = 100, VT= 26mV and VA =00, For the circuit shown below and for I1= 3 mA,…

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.