A prismatic vessel has two sections A and B connected by an orifice 0.3m square with C = 0.60. The horizontal cross -section of A is 10 sqm and that of B is 40 sqm. At a %3D certain time, the water in A is 6m above the center of the orifice and in B is 3m. Compute the discharge from A to B. 0.38 cubic meters per second 0.55 cubic meters per second O 0.50 cubic meters per second 0.41 cubic meters per second

A prismatic vessel has two sections A and B connected by an orifice 0.3m square with C = 0.60. The horizontal cross -section of A is 10 sqm and that of B is 40 sqm. At a %3D certain time, the water in A is 6m above the center of the orifice and in B is 3m. Compute the discharge from A to B. 0.38 cubic meters per second 0.55 cubic meters per second O 0.50 cubic meters per second 0.41 cubic meters per second

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C = 0.60. The horizontal cross –section of A is 10 sqm and that of B is 0.40 sqm. At a certain time, the water in A is 6m above the center of the orifice and in B is 3m. a. Compute the discharge from A to B. b. Find the time in which the water surfaces in the two tanks will reach the same elevation. c. Howsoon thereafter will the water surface be 1m apart?
What is the gross head (m) of a small hydroelectric dam that can produce 10 kW ofpower if the penstock discharge is 1,500 li/min?
Calculate the theoretical discharge through a vertical orifice 0.3 m square in the side of a tank if the free surface of the liquid in the tank is 150 mm above the top edge of the orifice. Compare this value with that obtained by multiplying the orifice area by the theoretical velocity at its center. Draw the figure properly.
Water at 30°C flows at the rate of 0.046 m /s through the through a 150-mm pipe in which along-radius flow nozzle 75 mm in diameter. What is the deflection of the mercury in the differential gage? Assume C= 0.98
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m). Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flow through the pipe, what must be the pressure at A?
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
Oil of density ρ=880 kg / m3 flows through the Venturi tube (pictured). Calculate the flow if given: D=24 mm, d=12 mm, h=440 mm. Need to solve it with bernoulli's equation.
Theoretically, what diameter of standard, sharp-edged orifice will be required to produce a discharge of 1.25 cfs of water under a head of 11.5 ft?
a horizontal venturimeter with inlet and throat diameters 160 mm and 60 mm respectively is used to measure the flow of an oil of specific gravity 0.8. If the discharge of the oil is 0.05 m3/s, find the deflection of oil mercury gauge. take venturimeter constant = 1
A sharp edged orifice will be required to produce a discharge of 35 liters/sec of water under a head of 3m. Find the required diameter, when C = 0.595