A process has 10 steps with yields Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 0.82 0.81 0.85 0.78 0.87 0.80 0.88 0.83 0.89 0.90 Create a table that shows operation step yields and cumulative rolled throughput yields. Determine the overall process rolled throughput yield. Plot the results. Describe manufacturing, business process, and/or Six Sigma project situations for the origination of this data. Include example operation steps to monitor. Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.

A process has 10 steps with yields Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 0.82 0.81 0.85 0.78 0.87 0.80 0.88 0.83 0.89 0.90 Create a table that shows operation step yields and cumulative rolled throughput yields. Determine the overall process rolled throughput yield. Plot the results. Describe manufacturing, business process, and/or Six Sigma project situations for the origination of this data. Include example operation steps to monitor. Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter4: Linear Programming Models

Section4.8: Data Envelopment Analysis (dea)

Problem 41P

See similar textbooks

Similar questions

Cablesplice, Inc.'s manufacturing process consists of five steps: making con- ductors, adding insulation, adding sheathing, irradiation, and printing and coil cuttingUnits are measured in meters. In 970,000 meters of cable, 700 defects were found in the conductors, and 75,000 defects were found in the insulation. In 440,000 meters of cable, 8,930 defects were found in the sheathing, and no defects were found in the remaining two steps. (a) Find DPU and the dpmo, and (b) the sigma level for each process step.
WAI knows from historical records that approximately 40percent of its labor is used in Department 101 and 60 percentis used in Department 102. Th e reverse is true of machine time;60 percent is used in Department 101 and 40 percent is used inDepartment 102.(a) Calculate the labor and machine hours needed inDepartment 101 for each period of the MPS developed inProblem 4.(b) Calculate the labor and machine hours needed inDepartment 102 for each period of the MPS developed inProblem 4.
A detailed map that identifies the specific activities that make up the informational, physical and/or monetary flows of a process is A. an activity on node map. B. a process map. C. an efficiency map. D. a benchmarking map.
Mazen has been an operations’ manager at XYZ company for the past 5 years. He holds many complex tasks and is required to stay connected and updated with information concerning the employees and the customers. Moreover, he is aware of the importance of consistently gathering, giving and receiving information.One day, he receives a financial report stating that sales for the past weekend have dropped about 10%. He assumes that this problem is caused by the recent increase in prices and doesn’t gather further information nor find alternatives to solve this problem. Mazen is being a: * 1 Problem avoider 2Problem solver 3 Problem seeker 4 Problem creator
An organization is considering three process configuration options. There are two different intermittent processes, as well as a repetitive focus. The smaller intermittent process has fixed costsof $30000 per month, and variable costs of $9 per unit. The larger intermittent process has fixed costs of $11000 per month and variable costs of $2 per unit. A repetitive focus plant has fixed costs of $48000 and variable costs of $1 per unit.a. If the company produced 22000 units, what would be its cost under each of the threechoices?b. Which process offers the lowest cost to produce 39000 units? What is that cost?
one thing i dont understand is when i asked the first question the precedence graph looks very different to the one for the third time i asked question satrting with 6C. in the picture it shows the difference between the two the answer is both the same 41 weeks. please chack the the first time i asked the question and then the third time i asked the graphs look different
State whether the following statements are true or false. If the statement is false, write its correct answer: 1. Process and Product design should be put in a way to reach customer satisfaction, and decrease profit and selling. Answer: 2. Operations management can be utilized in Process design, for it is beneficial to reduce the value of the product at every phase of its production. Answer: 3. A flow chart is a diagram that uses arrows and different symbols to represent consecutive events of a workflow or process. Answer: 4. The five key performance factors to access a process performance are: quantity, speed, dependability, flexibility and cost. Answer: 5. The process design consists of different steps and stages that are classified in an unorganized order, for the successful creation of the final product. Answer: 6. In the service industry, it’s possible to separate service design from process design. Answer: 7. Design is any part of an organization which…
XYZ Company produces and sells 2 products, Lambda and Gamma, and the production process goes through two departments. Traditionally Manufacturing Overhead (M/O) cost is applied on the basis of direct labor hours (DLH); estimated M/O cost is $ 5,757,500 and the estimated DLH is $12,250 for the most recent period.The team decided to replace traditional plantwide costing system to activity-based costing system. There are 3 activity cost pools which represent 3 activity areas at the plant. Direct Labor wage rate is $ 30 per hour. Compute total cost per unit (for lambda and gamma) using activity-based approach. (round your numbers).
Describe the bounds, limitations, requirements, proportional relationships, and balance constraints: Korey is a business student at State U. She has just completed a course in decision models, which had a midterm exam, a final exam, individual assignments, and class participation. She earned an 86% on the midterm, 94% on the final, 93% on the individual assignments, and 85% on participation. The benevolent instructor is allowing his students to determine their own weights for each of the four grade components—of course, with some restrictions: The participation weight can be no more than 15%. The midterm weight must be at least twice as much as the individual assignment weight. The final exam weight must be at least three times as much as the individual assignment weight. The weights of the four components must be at least 10%. The weights must sum to 1.0 and be nonnegative.
Great Valley Income Tax Advice GV is a small accounting firm supporting wealthy individuals in their preparation of annual income tax statements. Every December, GV sends out a short survey to their customers, asking for the information required for preparing the tax statements. Based on 50 years of experience, GV categorizes their cases into the following groups: Group 1 (new customers, easy): 15 percent of casesGroup 2 (new customers, complex): 5 percent of casesGroup 3 (repeat customers, easy): 50 percent of casesGroup 4 (repeat customers, complex): 30 percent of casesHere, “easy” versus “complex” refers to the complexity of the customer’s earning situation. In order to prepare the income tax statement, GV needs to complete the following set of activities. Processing times (and even which activities need to be carried out) depend on which group a tax statement falls into. All of the following processing times are expressed in minutes per income tax statement. The activities are…
Tasty Tim’s is a specialty taco restaurant. The following tasks are required for the successful assembly of a Tasty taco (times are in seconds per taco): Chop and trim meat – 30 Chop vegetables – 20 Grill meat – 240 Grill vegetables – 180 Prepare toppings - Lettuce - 10 - Tomato - 15 - Guacamole - 40 Assemble taco - Add meat - 5 - Add vegetables - 5 - Add cheese - 5 - Add toppings - 10 Wrap taco - 20 During the lunch hour, Tasty Tim’s encounters demand for 120 tacos. What is the Takt time (in seconds/unit) takt time for Tasty Tim’s taco shop?
The sales forecast for a certain product being sold at P300/bundle is P25M/month. Each bundle has 100 packs with a weight of 30grams/pack. The product undergoes the following manufacturing processes: PROCESS CAPACITY/UNIT COST/UNIT EFFICIENCY Kneading 200kg/hr P800,000 85% Cutting 60kg/hr 600,000 90 Drying 500kg/hr 1,200,000 100 Seasoning 75kg/hr 100,000 100 Packaging 2,400packs/hr 250,000 95 If the company is operating at 25 days/month @ 24-hour operation, how much money is needed for the procurement of the machines? How many factory workers are needed in a 2-shift operation if kneading requires 2 operators, cutting - 2, drying - 1, seasoning - 1 and packaging - 3?