A pump 254mm suction pipe and a 127mm discharge pipe is use to deliver 52L/s of water. The suction gage reads 120mmHg vacuum and the discharge gage located 100 cm above the suction gage which reads 108 kPa gage. Find the ff: (a) TDH in meter, (b) water power in kW, (c) If the power of the driving motor is 15 Hp, what is the pump efficiency? Answers: 14.45m; 9.978hp, 65.85%

A pump 254mm suction pipe and a 127mm discharge pipe is use to deliver 52L/s of water. The suction gage reads 120mmHg vacuum and the discharge gage located 100 cm above the suction gage which reads 108 kPa gage. Find the ff: (a) TDH in meter, (b) water power in kW, (c) If the power of the driving motor is 15 Hp, what is the pump efficiency? Answers: 14.45m; 9.978hp, 65.85%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump discharged 20 L/s against a head of 17 m when the speed is 1500 rpm. The diameter of the impeller was 38 cm and the brake horsepower is 6. A geometrically similar pump 49 cm in diameter is to run at 1750 rpm, assuming equal efficiencies, what brake power is required in Hp?
Steam enters a horizontal turbine at 350 lbf/in 2 absolute,580 ° C, and 12 ft/s and is discharged at 110 ft/s and 25 ° Csaturated conditions. The mass fl ow is 2.5 lbm/s, and theheat losses are 7 Btu/lb of steam. If head losses are negligible,how much horsepower does the turbine develop?
A gasoline pump fills a 80-L tank in 1 min 30 s. If the pump exit diameter is 4cm, what is the average pump-flow velocity?
A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 120 cm above the suction gage which reads 110 kPa gage. Determine: a. The total dynamic head (TDH) in meters b. The water power in kW c. The pump efficiency in % if the power supplied by the motor is 15hp
A Pitot tube at a height of 3 m, measures wind velocity 5.3 m/s. What is the wind velocity at a height of 50 m? If the center of a 45 m diameter wind turbine is placed at 50 m, what is the maximum power this turbine may produce?
Please anybody answer this ASAP,i need the answer in 40 min Air flows isentropically through a channel To = 310 ° C. The two ends have identical areas, namely A = 25 cm², pressure p1 = 160 kPa and p2 = 65 kPa Determine a). Mass flow rate, b). Throat area and C). Ma2
A certain 15-Kw pump running at 1600 rpm has an inlet diameter of 20cm and the discharge line is 12 cm in diameter. The output from th pump is 2800 liters/min of 20C and the centerline of the pump discharge is 1.5 meter above the centerline of the intake pipe. Determine the efficiency of pump. Please show complete solutions and formulas used. Show schematic diagram too.
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.85 L/s, with an output pressure of 3.05 × 105 Pa. a. The water enters a hose with a 2.8 cm inside diameter and rises 2.4 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. ( dont forget to convert the diameters of pipes into meters.) b. The hose then goes over the foundation wall, losing 0.35 m in height, and widens to 4.4 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses. ( dont forget to convert the diameters of pipes into meters.) Note: answer iS NOT 3.29 x 10^5 for either of these.
The inlet section of a vacuum cleaner is a rectangle 1 in x 5 in.The blower is able to provide suction at 25 ft3/min. Assuming theair density is 1.2 kg/m3, what is the mass flow of air in kg/s?
Air fl ows through a variable-area duct. At section 1, A1 =20 cm2, p1 = 300 kPa, ρ1 = 1.75 kg/m3, and V1= 122.5 m/s.At section 2, the area is exactly the same, but the density ismuch lower: ρ2 = 0.266 kg/m3 and T2 = 281 K. There is notransfer of work or heat. Assume one-dimensional steady flow.(a) How can you reconcile these differences? (b) Find the massflow at section 2. Calculate (c) V2, (d ) p2, and (e) s2 - s1.[Hint: This problem requires the continuity equation.]
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
The diameter of pipe carrying water changes gradually from 20mm at A to 450mm at B. A is 4.57m lower than B. What will be the difference in pressure,in N/mm2, between A and B, when 0.176cu.m/s is flowing loss of energybeing neglected?