A pump is 2.2 m above the water level in the sump and has a pressure of -20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine: (1) The discharge. (i) The power input into the flow by the pump. (1) The elevation, above the water sump level, to which the jet would reach. Neglect all losses 11 Nozzle 25 on dia 4.2m

A pump is 2.2 m above the water level in the sump and has a pressure of -20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine: (1) The discharge. (i) The power input into the flow by the pump. (1) The elevation, above the water sump level, to which the jet would reach. Neglect all losses 11 Nozzle 25 on dia 4.2m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 1.64 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.94 m.
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
A 20 hp pump with a suction from an open reservoir (10 m abovethe pump) has a flow rate of 125 m3/hr and a suction pipe of 150mm diameter. Determine the discharge pressure of the pump if itpumps water to a tank 15 m above the pump. Discharge pipediameter of the pump is 100 mm.
The owners of a smallholding water their vegetable garden using collected rainwater from atank. Thetankhasadiameterofbm,itisam tall and sits on a 6 m tall stand. The inner diameter of the hose is c cm, and the hose is (20 +5d) m long. If the tank was initially filled to the brim, how long will it take before the tank is empty? Assume that there is a single ball valve (K = 0.05) in the line, and that the spray nozzle has a hole diameter that is 20 % of the diameter of the hose. You may ignore all other losses in the nozzle. a = 9 b = 8 c = 7 d = 1 Hint: Use an Excel spreadsheet or C program for the calculations.
A Francis turbine is installed with a vertical draft tube. The top of the draft is 1.0 m below thecenter line of spiral casing while the tail race water level is 3.0 m from the top of the draft tube. There is no velocity of whirl at the top or bottom of the draft tube and leakage are negligible. Theelevation of water from the reservoir to the center line of the turbine spiral casing is 50 m, and watervelocity at the inlet is 5 m/sec. Discharge is 2.5 cu.m/sec, hydraulic efficiency is 86%, overallefficiency of 83%. Determine the reading of a pressure gage (in psi) if one is installed at thepenstock just before the water inlet to the turbine.
water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter is 21 cm. the pressure at the inlet is 775 kpa and at the throat is 584 kPa. determine the discharge in L/s. neglect head lost.
A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 2.5 m above the outlet. The tank air pressure above the water level is 250 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank.
4. Hydroelectric plants in the mountains bring water from a reservoir down to a turbine through enclosed tubes. In such plants, the 100 cm diameter intake tube (Point 2) in the dam is 50m below the water surface (Point 1) of the reservoir. The water drops 200 m through the tube before flowing into the turbine through a 50 cm diameter nozzle.
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
Water flows through a venturi meter whose inlet diameter is 31 cm and throat diameter is 19 cm. The pressure at the inlet is 755kPa and at the throat 550 kPa. Determine the discharge in cumecs. Neglect head loss.
ME Board - October 2002 Water is to be raised to a height of 25 meters at 20 kg/s. Inlet diameter is 16 cm, exit diameter is 12 cm and heat loss is 2 kW. Determine the power input to the pump.
A handheld bicycle pump can be used as an atomizer to generate a fine mist of paint or pesticide by forcing air at a high velocity through a small hole and placing a short tubebetween the liquid reservoir and the high-speed air jet whose low pressure drives the liquid up through the tube. In such an atomizer, the hole diameter is 0.3 cm, the vertical distance between the liquid level in the tube and the hole is 10 cm, and the bore (diameter) and the stroke of the air pump are 5 cm and 20 cm, respectively. If the atmospheric conditions are 20°C and 95 kPa, determine the minimum speed that the piston must be moved in the cylinder during pumping to initiate the atomizing effect. The liquid reservoir is open to the atmosphere