A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
Q: A constant wind blowing against the side of this chimney has caused creeping strains in the mortar…
A: Let us consider the height of the chimney is h and having constant cross-section against wind, the…
Q: A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…
A:
Q: 25. A metal pipe of 1 m diameter contains a fluid having a pressure of 1 N/mm?. If the permissible…
A:
Q: As shown in the figure, a bolt with a diameter of 10 mm is affected by three separate forces in…
A:
Q: A scuba tank is being designed for an internal pressure of 1600 psi with a factor of safety of 2.0…
A:
Q: A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What…
A:
Q: A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…
A:
Q: The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in…
A: Given Outer diameter = 6.2 in Thickness = 0.75 in Weight = 62 kips Torque = 185 kip-in To find…
Q: A punch for making holes in steel plates is shown in Figure 4. Assume that a punch having diameter d…
A:
Q: Estimate: 1- The normal stress in the bar. 2- The change in the length, if its original length…
A:
Q: Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Calculate the force which can be applied in the punch shown in the figure if the allowable shear…
A:
Q: Example 125. In figure below, assume that a 20-mm-diameter rivet joins the plates that are each 110…
A: Given data: Diameter of rivet, d = 20 mm. Width of the plate, w = 110 mm. Allowable bearing stress…
Q: A wooden bar is subjected to a tensile stress of 5 MPa. What will be the values of normal and shear…
A: Given data: The tensile stress in wooden bar is σ = 5 MPa. The angle between the section and the…
Q: A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force…
A: Given Data The diameter of the pulley is: D=1.2 m the diameter of the shaft is: d=5 in=127 mm The…
Q: Assume that the axial load P applied to the lap joint is distributed equally among the three…
A: Answer: The maximum allowable value of load that can be applied on the joint is 37.7 kN.
Q: 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is…
A:
Q: What is the stresses in the rail at 50°C , if there is an expansion allowance of 5 mm per rail .
A: Given data: The temperature of the rail is Tf = 50oC. The expansion allowance is l = 5 mm.
Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…
A: Given Outside diameter, d2 = 0.8 in Inside diameter, d2 = 0.19 in…
Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…
A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress
Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness…
A: Given data for aluminum cylinder 2014-T4
Q: . Find the thickness of the flat end cover plates for a 1 N/mm2 boiler that has a diameter of 600…
A:
Q: A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…
A:
Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…
A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…
Q: Problem no. 1 A rectangular post which is made up of two blocks of wood glued together along a joint…
A: Given: The shear and normal stresses in glue are 21755.7 psi and 17404.5 psi respectively. Axial…
Q: 2. A punch for making holes in steel plates is shown in Figure - 2 (a & b). Assume that a punch…
A:
Q: A rubber block with dimensions 120x120x120 mm is a rigid mold It is compressed with a vertical force…
A:
Q: A 6 mm thick plate is to be punched of a shape shown in figure. Determine the minimum punching force…
A:
Q: Two strip of metal are pinned to gather as shown in fig below with a rod of 10 mm diameter. The…
A: Given Information: The diameter of the rod (d) = 10 mm The ultimate shear stress of the rod (S) = 60…
Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…
A: Given A steel bolt Tensile load P=40kNMajor diameter(d1)=6 mmMinor diameter d2=4 mmAverage tensile…
Q: QUESTION 8 Rectangular bar of brass with cross section 4.2 mm x 7 mm and Young's modulus 97 GPa…
A:
Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…
A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…
Q: Assume that the axial load P = 40KN applied to the lap joint is distributed equally among the three…
A:
Q: mm thickness is compressed between two flat dies, and μ = 0.1 determine sticking radius and load on…
A:
Q: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the…
A: Given: d=100mm Syt = 250 MN / m2 Sys = 140 MN / m2 E = 200 GPa μ=0.3 N = 2
Q: A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm.…
A: Write the given data. t=15 mmD=460 mmH=2.5 mσL=120 MPaσc=50 MPa
Q: For a punching operation shown in the figure, compute the shear stress in the material if the force…
A: The punching operation is based on shear stress generation over inner and outer surface of the…
Q: A punch for making holes in steel plates is illustrated above. Assume that a punch having a diameter…
A: Given:Thickness of plate, t=10 mm or 0.010 mdiameter of punch, d=20 mm or 0.020 mForce, f=120 kN or…
Q: 2) An idealized free-body diagram of a door handle is shown below. To simplify, member X-Y is only…
A: Given: Let us consider the given data, M=1500×0.100=150 NmT=1500×0.2=300 Nmdiameter,d=20 mm=bσ= 3MPa
Q: A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the material…
A: Compressive load on the rod, P=350 kN=350*103 N Permissible stress for the material, σ=52.5 N/mm2
Q: 4. A ring made of 2.5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…
A: We know that a ring composed of steel bar with a diameter of 2.5 cm has a draw of 10 kN. The maximal…
Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…
A: Given data: The magnitude of the load, F = 3000 kN. The diameter of the pin, d = 0.3 m. Calculate…
Q: he pin in the image shown must transfer an axial tension force of 12.7 kN. Calculate the minimum pin…
A:
Q: For a steel beam loading, the maximum normal compressive stress is - 6 MPa, maximum normal tensile…
A:
Q: A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and…
A: Given data The tensile stress σ = 5 MPa. angle between the section and the tensile stress is θ =…
Q: In a tensile test on a steel tube of external diameter 18 mm and internal diameter 12 mm, an axial…
A: Given data To determine poisson's ratio and ther modulus
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
Step by step
Solved in 2 steps with 2 images
- (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
- A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
- Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
- A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa