A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and shear stress across a section, which makes an angle at 250 with the direction at the tensile stress

A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and shear stress across a section, which makes an angle at 250 with the direction at the tensile stress

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: Calculate the stress developed in a steel rod that is 25 mm in diameter when a 70kNaxial tensile…

A: Diameter of rod=d= 25 mm Cross- sectional area= A= (π/4)×d2 = (π/4)×252= 490.873 mm2 Axial load=P=…

Q: .A link in a packaging machine mechanism has a square cross section of 0.40 in on a side. It is…

Q: a triangular distributed horizontal force of peak intensity (see the figure). The length of the

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: Area of copper = 2 in2 Area of aluminium = 3 in2 Allowable stress of copper = 20 ksi Allowable…

Q: A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What…

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: E=PA∆LL⇒EA∆LL=P

Q: Example 125. In figure below, assume that a 20-mm-diameter rivet joins the plates that are each 110…

A: Given data: Diameter of rivet, d = 20 mm. Width of the plate, w = 110 mm. Allowable bearing stress…

Q: A bar is applied a tensile load of 50 kN having diameter 10 mm, Calculate the tensile stress induc

A: Given:force, F=50 kNdiameter, d=10 mm

Q: Two plates 20 mm thickness are fastened by a number of 25 mm diameter rivets, a tensile load of 500…

Q: A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force…

A: Given Data The diameter of the pulley is: D=1.2 m the diameter of the shaft is: d=5 in=127 mm The…

Q: A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as…

Q: 4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…

A: Given: The diameter of ring, d = 2.5 cm 0.025 m The load, P = 10 kN The mean radius, R = 15 cm =…

Q: Consider a plane of area 30 m^2 in a bar. The bar is subjected to tensile force of 5 kN. Calculate…

A: Given data: The area of the plane of the bar is A=30 m2 The tensile force in the bar is P=5 kN The…

Q: Compute the stress in a round bar subjected to a direct tensile force of 3200 N if the diameter of…

A: Given data: F=3200 Nd=10 mm Need to determine the stress in a round bar.

Q: An eye bolt carries a tensile load of 20 kN. Find the size of the bolt , if the tensile stress is…

Q: An axially loaded bar has normal stress 173 MPa. The shear stress in the bar is

A: given data : Maximum principal stress (σ1)=173 MPaMinimum principal stress (σ2)=0

Q: A uniform concrete slab of mass M is to be attached to two rods whose lower ends arw initially at…

A: Given, Steel: LS=3 m=3000 mmAS=300 mm2ES=200 GPa=200×103 MPa Aluminum: LAl=6 m=6000 mmEAl=70…

Q: 100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is…

A: Given Load= 100 kN Maximum shear stress = 70 MPa Cursing stress = 100 MPa To find Diameter…

Q: 2.49. A bar of rectangular cross section 20 mm x 3 mm has a central hole of diameter 6 mm. Find the…

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: Problem no. 1 A rectangular post which is made up of two blocks of wood glued together along a joint…

A: Given: The shear and normal stresses in glue are 21755.7 psi and 17404.5 psi respectively. Axial…

Q: 10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were…

A: Given: Number of rivets→n=10 Diameter of the each rivet→d=1.25 inch Hence area for shear…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Given A steel bolt Tensile load P=40kNMajor diameter(d1)=6 mmMinor diameter d2=4 mmAverage tensile…

Q: An elastic member 18.7 mm thick is glued in between two rigid members. Considering a shear force of…

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: A 1.25 inch diameter hole is drilled on the centerline of a steel bar 3.5 inches wide by 3/8 inches…

Q: (i) Calculate the normal stress o on the upper part of the post. (ii) If it is desired that the…

Q: A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm.…

A: Write the given data. t=15 mmD=460 mmH=2.5 mσL=120 MPaσc=50 MPa

Q: What force is required to compress a 200mm diameter hollow post with a thickness of 50mm thickness…

A: Given Data⇒ Internal diameter of hollow post(d)=200 mm Since 1 m=1000 mm Internal diameter of hollow…

Q: A two spring is connected in parallel attached to a single load. The maximum allowable stress is…

A: Given that, Allowable stress, σ=200 MPa,Spring 1, d=33 mm,n=18,R=120 mm,Spring 2,d=30 mm,n=20,R=100…

Q: A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the…

Q: 2. A point in a strained material is subjected to a tensile stress of 50 MPa. Find the normal and…

Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…

A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN

Q: A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch…

Q: 2.49. A bar of rectangular cross section 20 mm × 3 mm has a central hole of diameter 6 mm. Find the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Calculate the design stress when a material has an ultimate strength of 120 psi with a factor of…

A: Answer: The design stress is 165.5 kPa.

Q: For a steel beam loading, the maximum normal compressive stress is - 6 MPa, maximum normal tensile…

Q: Two plates are held together by 4, 28 mm diameter bolts. If a 25 kN load is applied to the plates in…

Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…

Q: Calculate the maximum stress in a 25 mm thick perforated bar and show its location o

A: Given:Force, F=5000 NMaximum stress occurs in the material where area of the material is less

Q: Calculate the axial stress in a tube that is stretched by a tensile axial force of 4500 N if the…

A: Write the given data. F=4500 Ndo=25 mm=0.025 mdi=20 mm=0.020 m

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of
normal stress and shear stress across a section, which makes an angle at 250 with the
direction at the tensile stress

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wooden bar is subjected to a tensile stress of 5 MPa. What will be the values of normal andshear stresses across a section, which makes an angle of 250 with the direction of the tensile stress andalso determine the maximum shear stress
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
A mild steel rod having a stress of 50 Mpa and having a diameter of 20 mm What is the force applied on it.
There is a tube from aluminium, which has an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what can the maximum force (in kN) that the member can support?
A wire with circular base of radius 3 mm was subjected to tensile stress of 13.5 N. If half the amount of stress is to be applied to a wire with square base of 1.86 mm width, what must have been the force (in Newton) applied to this new wire?
a short square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000 lbs. calculate the shear stress and the tensile stress acting on the plane which is mormal and is inclined 50 degrees to the longitudinalm axis of the bar. what is the factor of safet for the bar?
A bar is applied a tensile load of 50 kN having diameter 10 mm, Calculate the tensile stress induced in the bar.
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
Calculate the maximum stress in a 5mm thick steel plate with an 18 mm diameter round hole, given h gross = 12cm and the tensile load is 8.5 kN. (Final answer in MPa) Please solve carefully, Specifically Area calculation.
A 1.25 inch diameter hole is drilled on the centerline of a steel bar 3.5 inches wide by 3/8 inches thick. Calculate the maximum load that can be applied to the bar without exceeding the maximum stress in the bar of 22,000 psi. Can you help me with this problem?
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?
3. A 5/8 in diameter circular rod supports part of a storage shelf in a warehouse. As products areloaded and unloaded, the rod is subjected to a tensile load that varies from 1800 to 150 lb.Draw a sketch of the variation of stress versus time, and compute the maximum stress,minimum stress, mean stress, alternating stress, and stress ratio, R. please also give the FBD every calculation, thanky ou