A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the pump work in KW if the mass flow rate is 0.5 kg/s O a. 88.6 kw ob. 12.3 kw ос. 349 kw o d. 95.7 kw A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the turbine work in KW if the mass flow rate is 1.2 kg/s O a. 2238 kW O b. 2000 kw ос. 1000kw o d. 1326 kw A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the cycle efficiency O a. 30 % O b. 44 % O c. 56 % od. 32 %

A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the pump work in KW if the mass flow rate is 0.5 kg/s O a. 88.6 kw ob. 12.3 kw ос. 349 kw o d. 95.7 kw A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the turbine work in KW if the mass flow rate is 1.2 kg/s O a. 2238 kW O b. 2000 kw ос. 1000kw o d. 1326 kw A Rankine cycle with a water boiler at 3.0 MPa. The cycle has the highest and lowest temperatures of 450°C and 45°C respectively. Determine the cycle efficiency O a. 30 % O b. 44 % O c. 56 % od. 32 %

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam turbine with rated capacity of 42,000 kW (actual work produced) operates with steam at inlet of 4200 kPa and 420°C, and discharges into a condenser at a pressure of 60 kPa. Assuming turbine efficiency of 0.85, determine the state of the steam at discharge and the mass flow rate of the steam.
A heat pump with refrigerant-134a as the working fluid is used to keep a space at 25°C by absorbing heat from geothermal water that enters the evaporator at 60°C at a rate of 0.065 kg/s and leaves at 40°C. Refrigerant enters the evaporator at 12°C with a quality of 15 percent and leaves at the same pressure as saturated vapor. If the compressor consumes 1.6 kW of power, determine the COP.
Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the working fluid, is to be powered by an adiabatic steam turbine, which is also driving a generator. Steam enters the turbine at 12.5 MPa and 500 ∘C500 ∘C at a steady rate of 27.30 kg/s27.30 kg/s and exits at 10 kPa and a quality of 0.8710.0.8710. Air enters the compressor at 98 kPa and 295.0 K295.0 K at a steady rate of 12.600 kg/s12.600 kg/s and exits at 1 MPa and 635.0 K.635.0 K. For air, MW=29.0 g/mol,MW=29.0 g/mol, ??=3.5R.Cp=3.5R. Note: The IUPAC sign convention for work is used. Work into the system has a positive value. What is the magnitude of the power delivered to the generator by the turbine?
Consider the following ideal cascade refrigeration system with pressures of 0.9, 0.4, and 0.12 MPa.If the lower cycle transfers 69kW of energy to the upper cycle, determine the mass flowrate of R-134A (in kg/s) in the upper cycle. a.0.3987 b.0.4114 c.0.3600 d.0.4480
A heat pump with refrigerant-134a as the working fluid is used to keep a space at 25°C by absorbing heat from geothermal water that enters the evaporator at 60°C at a rate of 0.065 kg/s and leaves at 40°C. Refrigerant enters the evaporator at 12°C with a quality of 15 percent and leaves at the same pressure as saturated vapor. If the compressor consumes 1.6 kW of power, determine the minimum power input to the compressor for the same rate of heat supply.
A heat pump with refrigerant-134a as the working fluid is used to keep a space at 25°C by absorbing heat from geothermal water that enters the evaporator at 60°C at a rate of 0.065 kg/s and leaves at 40°C. Refrigerant enters the evaporator at 12°C with a quality of 15 percent and leaves at the same pressure as saturated vapor. If the compressor consumes 1.6 kW of power, determine the rate of heat supply.
Steam enters the high-pressure turbine of a steam power plant that operates on the reheat Rankine cycle at 10 MPa and 600°C and leaves at 4 MPa. Steam is then reheated to 500°C before it expands to a pressure of 30 kPa. The enthalpy of steam is 3330 kJ/kg at the exit of the high-pressure turbine, and 2600 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, the cycle efficiency is
1.A piston-cylinder device contains air at 427 degrees and 134kPa. A pressure increase of 1.378kPa was recorded after the air was compressed isentropically with minimum work input of 1.422KJ. Assuming air has constant specific heats evaluated at given temperature. Determine the mass of air in the device. 2. Air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300k, and a turbine inlet temperature of 1000k. Determine the required mass flow rate in (kg/s) of air for a net power output of 70MW, assuming both the compressor and the turbine have an isentropic efficiency of 100%. Assume constant specific heats at room temperature
The 7FA gas turbine manufactured by General Electric is reported to have an efficiency of 35.9 percent in the simple-cycle mode and to produce 159 MW of net power. The pressure ratio is 14.7 and the turbine inlet temperature is 1288°C. The mass flow rate through the turbine is 1,536,000 kg/h. Taking the ambient conditions to be 20°C and 100 kPa, determine: (a) the isentropic efficiency of the turbine and the compressor, (b) the thermal efficiency of this gas turbine if a regenerator with an effectiveness of 80 percent is added. Answers: (a) 0.849, 0.924 (b) 0.496
A heat pump using refrigerant-134a heats a house by using underground water at 8°C as the heat source. The house is losing heat at a rate of 60,000 kJ/h. The refrigerant enters the compressor at 280 kPa and 0°C, and it leaves at 1 MPa and 60°C. The refrigerant exits the condenser at 30°C. Investigate the effect of varying the compressor isentropic efficiency over the range [60 to 100 percent]. Plot the power input to the compressor and the electric power saved by using a heat pump rather than electric resistance heating as functions of compressor efficiency and discuss the results.
Try to explain why a certain amount of thermal energy rejected intentionally in condensers and pumps are employed instead of compressors in steam power cycles?
The efficiencies of all reversible heat engines operating between the same two reservoirs are the same?