7 Elevation - 42.7 mElevation- 27.4 mL-608 mD-20 emL304 m D 20 cm- Elevation - 12.2 mFigure 2: Pumping from lower to higher elevation Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by the pump (in kilowatte) talpump water at 0.085 m/sat 20°C from the lower to the upper reservoir?Deo AFiguro 2: Pumping from lower to higher elevationThe head loss in the pipes is h, 0.018 where Lis the length of the pipe in metors, and D is the diameter of the pipe in meters.D 25Sketch the HGL and EGL for the system

Answered: Image /qna-images/answer/785868c6-0269-4d43-93f2-a7831926027a.jpg

Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by the pump (in kilowatte) tapump water at 0.085 m/s at 20°C from the lower to the upper reservoir? Deo A Figure 2. Pumping from lower to higher elevation The head loss in the pipes is h 0.018 . where Lis the length of the pipe in metors, and D is the diameter of the pipe in meters. D 29 Sketch the HGL and EGL for the system

Figure 2 is a schematic of a pumped-storage system. How much power must be supplied to the water by the pump (in kilowatte) tapump water at 0.085 m/s at 20°C from the lower to the upper reservoir? Deo A Figure 2. Pumping from lower to higher elevation The head loss in the pipes is h 0.018 . where Lis the length of the pipe in metors, and D is the diameter of the pipe in meters. D 29 Sketch the HGL and EGL for the system

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pumped storage power plant with a head of 150 m, with a flow rate of 6 cms for power generation and pumping, and continuous operation for 8 hours each time. Try to find (1) the power output during power generation and the total daily power generation; (2) pumping water Hourly power and total daily power demand; (3) Pumped storage power plant efficiency; (4) Adjust the pool capacity? Assuming that the water loss is 8% of the total drop, the combined efficiency of the turbine and generator is 85%, and the efficiency of the pump is 65%.
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet is Show FBD and choose th correct answer A. 7.12 B. 6.21 C. 5.05 D. 8.7
In Fig. is shown a plot of pump net head as a function of pump volume flow rate, or capacity. On the figure, label the shutoff head, the free delivery, the pump performance curve, the system curve, and the operating point.
A pump draws 20 m3/h of water having a density of 1000 kg/m3 from the open storage feed tank to an open overhead tank that supplies 151 J/kg to the wallowing fluid. What is the horsepower hp of the pump if it’s efficiency is 75%? The flow turbulent
A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The total length of the suction and discharge pipes are 7.1 m and 12 m, respectively. All pipes uses 2 in.-diameter PVC pipes (ε = 0.15 mm). The elevations are shown in the figure below. Calculate the power input (in kW) to the pump if pump efficiency is 86% and motor efficiency is 96%. Take the density of water to be 1000 kg/(m^3) and μ = 1.00E-3 Pa-s.
The minimum fresh air requirement of a residential building is specified to be 0.35 air change per hour (per ASHRAE standards). That is, 35% of the entire quantity of air contained in a residence should be replaced by fresh outdoor air every hour. The ventilation requirement of a 3-meter highresidence with 150 square meters of floor space is to be met by air provided by a single fan.a. Determine the required flow capacity of the fan (in m3/min).b. Find the diameter of the fan duct required (circular cross-section) if the average air velocity from the duct is to be 3 m/sec.
A pump has a head of 20m at 450rpm. What is the increase in head developed by the pump if speed increase to 1000rpm? ANSWER: 78.76 m
include a free body diagram Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet isA. 6.21B. 7.12C. 8.7D. 5.05
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
Consider Fig. 1, the tank (with volume of 50 m3) must be filled up with water within 5 minutes. Take L1 and L2 as 5.2 m and 2.2 mrespectively: (a) determine the pumping power requirement, by assuming your own materials for the pipe of L1 and L2; (b) propose the details of the pump design (thickness of the pump etc), assuming that the pump is a vane pump while the volumetric efficiency of the pump is 0.95;
A pump is to deliver water at a head of 40 m, the water temperature being 38oC and barometric pressure is 760 mm Hg. At intake, the pressure is 432 mm Hg and the velocity is 3.50 m/s. Determine the NPSHA.
Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference between the pool and the storage tank is 60 m. The stórage tank and the pool are open to atmosphere. 50 meters of 6 in Sc 40 steel pipe is used between pool andpump. After the pump 6 in Sc 40 pipe with a length of 22 m is suddenly contracted to 4 in Sc 40 pipe, that is 70 m. The flow rate of water is 2.5 m/min and the temperature is 20°C. If the pump efficiency is 0.6 and the cost of electrical energy is 0.40 TL/kWh,calculate daily cost of electricity used for this system