A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum deflection is -4.2545793720899mm. BEAM'S DIMENSION: Width = 130mm, Height = 490mm NOTE: L = 5.5m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) w B Solve the maximum moment of the beam. kN-m Determine the shear at midspan.

A rectangular beam carries a triangular load "w" as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPa and the maximum deflection is -4.2545793720899mm. BEAM'S DIMENSION: Width = 130mm, Height = 490mm NOTE: L = 5.5m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) w B Solve the maximum moment of the beam. kN-m Determine the shear at midspan.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PLEASE ANSWER ASAP AND REFER TO THE GIVEN VALUES BELOW. THANK YOU!! For the beam loaded as shown in the figure below, determine the deflection at midspan in mm using ANY GEOMETRIC METHOD. Consider 300 mm x 500 mm (b x h) section and E = 200 GPa. Enter absolute value only. Use a = 3.7 m, b = 22.4 kN/m, and c = 27.3 kN
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Round-off to 3 decimal places. a = 8.5 m, b = 3.3 m, c = 9.5 kN/m, d = 27 kN-m. - Slope of the elastic curve at B in degrees. Indicate negative sign as necessary. - Deflection at D in mm. Indicate negative sign if downward. - Deflection at midspan in mm. Indicate negative sign if downward.
Distance is measured as 605.75m with a 50-m tape supported on quarters with a pull of 6.5kg. The standard pull of the tape is 5.2kg; its weight is 1.10kg, E=2.02x10^6 kg/sqcm, and the unit weight is 0.03kg/cubic cm. a. What is the correction due to tension? b. What is the total correction due to sag? c. What is the corrected length?
For the beam loaded as shown in the figure 3, determine the deflection at midspan of the beam in mm using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section and E=200 GPa Enter the absolute value only and round off your answer to 3 decimal places PLS. ANSWER ASAP, I'LL RATE. THANKS
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
determine the deflection at C in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places answer asap.
Using DOUBLE INTEGRATION METHOD. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 3.5m b = 16 kn/m c = 16 kn QUESTIONS: 1. Determine the REACTION at A in KN. 2. Determine the SLOPE at A in DEGREES. 3. Determine thw DEFLECTION at B in MM. 4. Determine the DEFLECTION at E in MM. THANK YOU!
reply asapp!! Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the first moment of area (statical moment of area), Q, of the diamond cross- section at the neutral axis? (in mm3) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation.
Develop the generalized piecewise equation for the elastic curve for the beam as a function of x referenced from A. Your equation should be in terms of P, x, and L. Take EI as a constant. NOTE: A is a pin support and B is a roller. Plot the deflected shape in excel for P = 10 kips, L = 15 ft, E = 29,000 ksi, and I = 150 in^4. Plot using 0.5 ft. increments for x.
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
Only accepted correct answer is 2.84. Please show solution. A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area.