A rectangular loop of area A=0.160 m2 is placed in a region where the magnetic field is perpendicular to the plane of the loop. The magnitude of the field is allowed to vary in time according to B=0.44e/2, where B is in teslas and t is in seconds. What is the value for induced emf ( in units of

A rectangular loop of area A=0.160 m2 is placed in a region where the magnetic field is perpendicular to the plane of the loop. The magnitude of the field is allowed to vary in time according to B=0.44e/2, where B is in teslas and t is in seconds. What is the value for induced emf ( in units of

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter24: Electromagnetic Waves

Section24.4: Energy Carried By Electromagnetic Waves

Problem 24.3QQ

See similar textbooks

Similar questions

You are working at NASA, in a division that is studying the possibility of rotating small spacecraft using radiation pressure from the Sun. You have built a scale model of a spacecraft as shown in Figure P33.47. The central body is a spherical shell with mass m = 0.500 kg and radius R = 15.0 cm. The thin rod extending from each side of the sphere is of mass mr = 50.0 g and of total length = 1.00 m. At each end of the rod arc circular plates of mass mp = 10.0 g and radius rp = 2.00 cm, with the center of each plate located at the end of the rod. One plate is perfectly reflecting and the other is perfectly absorbing. The initial configuration of this model is that it is at rest, mounted on a vertical axle with very low friction. To begin the simulation, you expose the model to sunlight of intensity Is = 1 000 W/m2, directed perpendicularly to the plates, for a time interval of t = 2.0 min. The sunlight is then removed from the model. Determine the angular velocity with which the model now rotates about the axle. Figure P33.47
A parallel-plate capacitor with dimensions of 12 mm by 9 mm and a plate separation of 1 micrometers exhibits a capacitance of 5 × 10-9 Assuming that the material is non-magnetic and the exhibits entirely electronic polarization, estimate its refractive index. εo= 8.854 × 10⁻¹² F·m⁻¹
The microwave radiation left over from the Big Bang has a maximummagnetic field strength of 2.33 x 10 -10 T. What is the correspondingmaximum electric field strength of the wave?
Which of the ff. absorption maxima is in the visible range of the electromagnetic spectrum? a.) 510 nm b.) 240 nm c.) 800 nm
The star Sirius is much hotter than the sun, with a peak wavelength of 290 nm compared to the sun’s 500 nm. It is also larger, with a diameter 1.7 times that of the sun. By what factor does the energy emitted by Sirius exceed that of the sun?
A totally reflecting disk has radius 8.00 mm and averagedensity 600 kg/m3. A laser has an average power output Pav spread uniformlyover a cylindrical beam of radius 2.00 mm. When the laser beamshines upward on the disk in a direction perpendicular to its flat surface,the radiation pressure produces a force equal to the weight of the disk.(a) What value of Pav is required? (b) What average laser power is requiredif the radius of the disk is doubled?
An electromagnetic wave from a wire antenna travels (from the reader) toward the plane of the paper. At time t = 0.0 s it strikes the paper at normal incidence. At point O and t = 0.0 s, the magnetic field vector has its maximum value, 5.01×10-8 T, pointing in the negative y-direction. The frequency of this wave is 1.17×106 Hz.What is the y component of the magnetic field at point O at time 4.27×10-7 s?
Calculate the displacement current Id between the square plates, 7.2 cmon a side, of a capacitor if the electric field is changing at a rate of 2.8×10^6 V/m*s Id=
A parabolic reflector focuses electromagnetic waves into a beam as shown in the figure. The electromagnetic radiation is pulsed, with a pulse frequency of 19.0 GHz, and the duration of each pulse is t = 1.00 ns. The face of the reflector has a radius of 3.00 cm, and the average power during each pulse is 29.0 kW. (Due to the nature of this problem, do not use rounded intermediate values in your calculations—including answers submitted in WebAssign.) (d) Determine the amplitude of the electric field (in kV/m) and magnetic field (in µT) in these electromagnetic waves. Emax= kV/m Bmax = µT (e) Assuming that this pulsed beam strikes an absorbing surface, compute the force (in µN) exerted on the surface during the 1.00 ns duration of each pulse. µN
When an electric current flows through the filament of an incandescent light bulb, it gets very hot and glows (or incandesces). Consider a particular bulb with a filament with 140 Ω resistance which carries a current of 1.00 A. Assume the length of the filament is L = 9.00 cm long with a radius of r = 0.900 mm. (a) Calculate the Poynting vector (in kW/m2) at the surface of the filament, associated with the static electric field producing the current and the current's static magnetic field. magnitude: ? kW/m2 direction: Radially inward or outward? (b) Find the magnitudes of the static electric field (in kV/m) and static magnetic field (in µT) at the surface of the filament. electric field: ? kV/m magnetic field: ? µT
In a region of space, the electric field is pointed along the x-axis, but its magnitude changes as described by Ex = (10 N/C) sin (20x − 500t) Ey = Ez = 0 where t is in nanoseconds and x is in cm. Find the displacement current through a circle of radius 3 cm in the x = 0 plane at t = 0 .