A rectangular lot was measured using a 100ft metallic tape which was 0.02 ft too long. The recorded distance were 231.20 ft long by 121.5o ft wide. Determine the error due to the erroneous length of the tape and actual area?

A rectangular lot was measured using a 100ft metallic tape which was 0.02 ft too long. The recorded distance were 231.20 ft long by 121.5o ft wide. Determine the error due to the erroneous length of the tape and actual area?

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter12: Forecasting Travel Demand

Section: Chapter Questions

Problem 15P

See similar textbooks

Related questions

Q: Compute the Area using the DMD and check by DPD method

Q: A triangular lot has been surveyed to determine its interior angles. The following values are…

Q: A rectangular lot was measured using a 50m steel tape which was later found to be 15mm too short.…

Q: questions by completing the tabulation below. Determine the total area of the lot in sq.m COMPUTED…

A: To find : Total area

Q: B. Describe a practical procedure to measure the height of your house using tachometric surveying,…

A: Tachometric Surveying: Tachometric Surveying is a type of surveying in which horizontal and vertical…

Q: What is the most probable value of a rectangular lot having the width and length of 239.01 ± 0.03 m…

Q: A rectangular lot was being measured using a 30-m metallic tape which was 6-mm too long. The record…

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: H.W\ Calculate the excavation volume from the details of cross sections shown in table below. The…

A: The volume of excavation is calculated by using trapezoidal formula.Each section of earth can be…

Q: A rectangular lot was measured using a 50 m steel tape which was found to a 0.025 m too short. if…

A: Given data- Correct length (scale) of the steel tapeC.S = 50 mScale 0.025 m too short⇒Wrong length…

Q: Using the average-end-area method, calculate the cut-and-fill volumes for stations 125 + 00 through…

A: Given:

Q: Fundamentals of Surveying: A rectangular lot was measured. The length was 16m with a probable error…

Q: 3.3 Using the average-end-area method, calculate the cut-and-fill volumes for stations 25 + 00…

A: Table is given having end area cut and end area fill

Q: From the given technical description of a lot, answer the following questions by completing the…

A: To find : 1) Total lot area in hectares

Q: Find the area of the lot using the given data.

Q: evations were obtained using 10m squares. PointA ner of the lot and D-4 at the southeast corner. A

A: (a) The scale utilized is 1cm = 2m . The line is displayed underneath. The cycle used to line a line…

Q: questions by completing the tabulation below. Determine the total area of the lot in hectares.…

A: Data Given: Asked: Complete the solution

Q: The technical description of a six-corner lot is tabulated in the table below. BEARING DIST LAT…

A: Latitude: The projection of a line on the north-south meridian which is equal to the multiplication…

Q: You take a 10% sample using 1/4 ac plots. If a total of 40 plots were sampled, what is the area of…

A: ASKED: To determine the area of the tract. Given, Sample size (say S) = 10% Plot area (say a) =…

Q: Q3) The figure below represent the horizontal coordinates (x, y) and vertical coordinate -ground…

A: Surveying a branch of the construction industry where balancing between different points on the…

Q: A parcel of land has been surveyed in the field and the lengths and bearings of the various sides…

A: The values given in the question are as follows: Lines Bearing Distance(m) AB N 53o 27' E 59.82…

Q: Briefly describe the following geophysical method for ground survey and the results it seek to…

A: Briefly describe the following geophysical method for a ground survey and the results it seeks to…

Q: The two sides of a rectangular lot were measured with certain estimated probable errors as follows:…

A: Given: The width is 253.36 ± 0.06 m. The length is 624.15 ± 0.08 m.

Q: Hi! Help me with this please. Thank you! If a large tract of land is to be subdivided into two…

A: Projection of line on North-South axis is called latitude while projection on East-West axis is…

Q: 3.2 Using the average-end-area method, calculate the cut-and-fill volumes for stations 19 + 00…

Q: From the given tract of land having the following data: LINES LATITUDE DEPARTURE А-B +40 -80 В-С +80…

A: The given values are as follow, To Determine ,The DMD of line AB The double area of the lot

Q: Calculate the corrected volumes of cut and fill using the following cross section notes, with the…

A: Given data:- Side slope, S = 1 Below table is given;

Q: During the time of the former president Fidel Ramos, a lot was surveyed and found out that the…

Q: A 50 m tape was used to measure a square lot that was 0.05 m too short. If the area of the lot is…

Q: Situation 1] A private parcel was surveyed prior to the construction of a proposed fabrication…

A: Given Table: By putting X=6, Y=6, Z=3

Q: situation 1] A private parcel was surveyed prior to the construction of a proposed fabrication…

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly…

Q: A 50m tape was used to measure a square lot that was 0.05m too short. If the area of the lot is…

A: Length of the tape, L=50m Length of the tape with error, L'=50-0.05=49.95m Measured area, MA=500m2…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

Q: What is the total length of the course AB if the rear tapeman holds exactly 5 pebbles and 3 pins…

A: 1 pin = 1 tape length1 Tally =10 tape lengths 1 pebble = 1tally

Q: The two sides of a rectangular lot were measured with certain estimated probable errors as follows:…

A: The width of rectangle lot, W = 324.36 Length of Rectangular lot, L = 568.15 Area of rectangle, A =…

Q: Balance the interior angles of the parcel shown below.

Q: the following values were determined in a series of tape measurements of a line: 300.58,301.23,…

Q: A parcel of lot (trapezoidal) has a technical description as shown in the tabulated data. Lines…

A: Procedure: In order to find the length of the dividing line, we need to find the values of m and n.…

Q: It is required to lay-out a building width=80m by length=100m with a 30m long metallic tape with…

A: Solution- LengthL=30mTape is 0.15m too longActual length of the tapeL'=30-0.15=29.85mBuilding…

Q: A private parcel was surveyed prior to the construction of a proposed fabrication plant. Table shown…

Q: An irregular lot was surveyed to obtain its area. Compute for the lot’s area using DPD method.…

Q: a. The base and altitude of a triangular lot were measured with certain estimated probable errors as…

Q: The sides of rectangular parcel of property were measured and recorded as 249.50 m and 496.85 m. It…

Q: The two sides of a rectangular lot were measured with certain estimated probable errors as follows:…

A: Given,L=624.15 m and B=253.36 msince δL=0.08 m δB=0.06 mtherefore,probable errors in length and…

Q: What is the total length of the course AB if the rear tapeman holds exactly 7 pebbles and 5 pins…

A: 7 pebbles =10 tapelengths1 pin=1 tape lengthSo,Total n =pebbles10+pinsLength of measurement =…

Q: A rectangular lot was being measured using a 30-m metallic tape which was 6-mm too long. The record…

Q: What is the total length of the course AB if the rear tapeman holds exactly 5 pebbles and 3 pins…

Q: A rectangular lot was measured using a 50m steel tape which was later found to be 15mm short. The…

A: procedure: First, find the actual but wrong length of tape which was found 15mm short then…

Q: Prepare the Lot Data Computation: balance by COMPASS RULE and Compute the Area by DMD Method

A: as the properties of the close traverse is the sum of all latitude and departure is equal to the…

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: To Determine Area bounded by straight road and an irregular boundary.

Q: The cross-section notes shown below are for a ground excavation. Sta. 25+100 7.85 0 8.45 1.90 3.2…

A: Step 1: Calculation of end areas: We will calculate the end areas of the given stations by…

Concept explainers

Professional survey

A professional survey is a systematic questionnaire that the target audience fills out online, usually by filling out google forms. Professional surveys can vary in length and format. The data is stored on a website and the testing tool usually provides a certain level of data analysis in addition to a professional expert review. Several professional online survey softwares are present worldwide like, SoGoSurvey, SurveyGizmo, SurveyMonkey, Qualtrics, and so on.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular lot was being measured using a 30-m metallic tape which was 6-mm too long. The record dimensions where 70.50-m long by 37.10-m wide. What is the error introduced due to the erroneous length of the tape? Calculate the error in the area.
The two sides of a rectangular lot were measured with certain estimated probable errors as follows: 253.36±0.06 m and 624.15±0.08 m. Determine the area of the lot and the probable error in the resulting calculation.
A rectangular lot was measured using a 30-m metallic tape which was 6 mm too long. The recorded dimensions were 70.50 m long and 37.10 m wide. What is the actual area?
show complete solution and formula What is the most probable value of a rectangular lot having the width and length of 239.01 ±0.03 m and 497.22 ± 0.03 m? Express your final answer in cm2
Station Cut End Area (ft2) 10+00 240 11+00 362 12+00 443 13+00 406 14+00 261 15+00 101 For the data tabulated above, calculate the volume of excavation between stations 10+00 and 15+00. Express your answer in cubic yards to five significant figures.
The two sides of a rectangular lot were measured with certain estimatedprobable errors as follows: W = 253.36 ±0.06m and L = 624.15 ±0.08m.Determine the area of the lot and the probable error in the resultingcalculation.
Determine the area bounded by a straight road and an irregular boundary using the data given below: STATION OFFSETS 0+000 8 0+020 6.25 0+040 8.43 0+060 6.75 0+080 8.28 0+100 5.86 Use the best method applicable. Round your answer to 3 decimal places.
A 50m tape was used to measure a square lot that was 0.05m too short. If the area of the lot is 5000m², what is the error in the computed area? Show complete solution 3 decimal places all final answers
The length of a water course passing through the fields was measured with 30 m steel tape and the measured length was equal to 4 Gunter’s chain and 2 Revenue chains. Later on, it was found that the tape was approximately half link of Gunter’s Chain too long. Find the true length of the line in meters. How many steps you have to walk to complete this measurement, if you perform this task?
The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 19+2600 8.09 5 0 5 8.25 6.54 5 4 6 6.7 Determine the cross sectional area at STA 19+2600. Round your answer to 3 decimal places.
A rectangular lot was measured using a 50m steel tape which was later found to be 15mm short. The recorded dimensions were 121.5m long by 93.5m wide. What is the error in the area?
determine the area of his lot which is shown below. use a combination of the Trapezoidal Rule and Simpson's 1/3 Rule for area computation. The data he gathered are as follows: h1 = 10.07 meters, h2 = 10.28 meters, h3 = 12.32 meters, h4 = 12.02 meters, h5 = 12.8 meters, h6 = 10.49 meters, h7 = 10.58 meters, d1 = 8 meters, d2 = 8 meters, d3 = 17 meters, d4 = 22 meters, d5 = 13 meters, d6 = 29 meters. What will be the resulting area (in hectares)?