A rectangular tension member is used resist a dead load of 85 kN and a live load of 200 kN. Use Fy = 248 MPa, Fu = 400 MPa, and diameter of the bolt is 20 mm. Use LRFD and ASD. a. Design the width of the section if the thickness is 12 mm. b. Design how many line of bolts can be used if the thickness is 12 mm.

A rectangular tension member is used resist a dead load of 85 kN and a live load of 200 kN. Use Fy = 248 MPa, Fu = 400 MPa, and diameter of the bolt is 20 mm. Use LRFD and ASD. a. Design the width of the section if the thickness is 12 mm. b. Design how many line of bolts can be used if the thickness is 12 mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.6P

See similar textbooks

Similar questions

A plate is used as a bracket and is attached to a column flange, as shown in Figure P8.2-3. Use an elastic analysis and compute the maximum bolt shear force.
Select a 30-ft long W12 section of A992 steel to support a tensile servicedead load of 130 kips and a tensile service live load of 110 kips. Asshown in the figure, the member is to have a two lines of bolts in eachflange for 7/8-in bolts (at least three in a line 4 in. on center).Use Fy = 50 ksi and Fu = 65 ksi.
A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3. 2-1. The steel is A36. Assume that Ae = An and compute the folowing. a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area
3.6-5 Use load and resistance factor design and select an American StandardChannel shape to resist a factored tensile load of 180 kips. The length is15 ft, and there will be two lines of 7⁄8-in. diameter bolts in the web, asshown in Figure P3.6-5. Estimate the shear lag factor U to be 0.85. (In apractical design, once the member and bolt layout are selected, the valueof U could be computed and the member design could be revised if necessary.)Use A36 steel.
The lap joint of a tension member is shown. The plate is 252mm wide and 12mm thick. The bolts are 20mm in diameter and the holes are 3mm larger than the bolt diameter. Steel A36 with Fy = 248 MPa and Fu = 400Mpa. It is required to determine the capacity of the joint based on gross area, net area, and block shear. a.) Determine the safe value of P based on gross area: Use Ft = 0.6Fy b.) Determine the safe value of P based on tension net area: Use Ft = 0.5Fy
A WT10.5 x 31 is used as a bracket to transmit a 60-kip service load to a W14 x 90 column, as previously shown in Figure . The load consists of 15 kips dead load and 45 kips live load. Four 7⁄8-inch-diameter Group A bolts are used. The column is of A992 steel, and the bracket is A36. Assume all spacing and edge-distance requirements are satisfied, including those necessary for the use of the nominal strength in bearing deformation (i.e., 2.4dtFu)*, and determine the adequacy of the bolts for the following types of connections: (a) bearing-type connection with the threads in shear and (b) slip-critical connection with the threads in shear.
A 2L 3 x 2 x ¼ LLBB tension double angle, A36 steel is subjected to a dead load of 12 kips and a live load of 36 kips. It is attached to a gusset plate with a line of 3/4-inch diameter bolts through the long legs. Does this member have enough stamina? Assume Ae= 0.85 in. Use LRFD.
Select a 30-ft-long W12 section of A992 steel to support a tensile service dead load PD = 130 k and a tensile service live load PL = 110 k.As shown in Fig. 4.1, the member is to have two lines of bolts in each flange for 7/8-in bolts (at least three in a line 4 in on center).
Use A36 steel and select a single-angle tension member to resist a service dead load of 13 kips and a service live load of 45 kips. Assume that the member will be connected to a 3⁄8- inch-thick gusset plate with a single line of five 7⁄8-inch diameter bolts. The member is 15 feet long. Note that the block shear strength failure must be consider for the design.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Ex: For a cantilever beam of length (L) subject 1 a concentrated load (P), shown in fgure, Find - 1 Max.tension and compression bending stress in beam section 2. Determine the proper spacing of the nails used 10 fix the flange boards to the web. The nals o be used can safely resist (F) of shearing force, given in 3 - “Table below. I»
Select a rectangular (not square) HSS for use as a 15-foot-long compression member that must resist a service dead load of 35 kips and a service live load of 80 kips. The member will be pinned at each end, with additional support in the weak direction at midheight. Use A500 Grade C steel. a. Use LRFD. b. Use ASD