A 27m3 CUBICAL TANK IS FULL OF TWO DIFFERENT FLUIDS OF EQUAL PARTS. AN OBJECT WAS THROWN AND WAS PARTIALLY SUBMERGED PROJECTING 15% ABOVE THE FLUID SURFACE. IF THE HEIGHT OF THE OBJECT IS 3m AND THE SPECIFIC GRAVITY OF THE FLUIDS ARE 0.9 AND 0.82, FIND THE SPECIFIC GRAVITY OF THE OBJECT. *

A 27m3 CUBICAL TANK IS FULL OF TWO DIFFERENT FLUIDS OF EQUAL PARTS. AN OBJECT WAS THROWN AND WAS PARTIALLY SUBMERGED PROJECTING 15% ABOVE THE FLUID SURFACE. IF THE HEIGHT OF THE OBJECT IS 3m AND THE SPECIFIC GRAVITY OF THE FLUIDS ARE 0.9 AND 0.82, FIND THE SPECIFIC GRAVITY OF THE OBJECT. *

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: At what altitude h above the north pole is the weight of an object reduced to 75% of its…

A: Given question: At what altitude h above the north pole is the weight of an object reduced to 75% of…

Q: 1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A…

Q: A Kaplan turbine of 100 B.H.P. is working under a head of 5 in and running at 210 R.P.M. The…

Q: Air is flowing steadily in an insulated duct. nd temperature measurements of the air at two stations…

A: GivenCp=1.005kJ/kgKh=CpTVT=0.287P

Q: Determine the angular velocity (positive if counterclockwise, negative if clockwise) of link BC for…

Q: Draw shear force and bending moment diagrams for the beam and loading in the figure.

A: Let HA and VA be the horizontally forward and vertically upward reaction at support A respectively…

Q: An engineer designing a light aircraft is trying to make an estimate of the diameter of the…

Q: For an interval of its motion the piston rod of the hydraulic cylinder has a velocity VA = 4.3…

A: Introduction: The instantaneous center of the velocity of a body is any place on a rigid body or its…

Q: /ft^3 Pump is said to delivers 233 gpm of water. The discharge elevation measured 3 ft. The…

Q: n aircon sizing, what do you think are other examples of factors affecting the heat load of a…

A: Air conditioning is the process in which the temperature of the outside air is maintained according…

Q: (lb) 900 -900 480 -1380 -x (10) Fig. (4)

Q: Which among the following is/are scalar quantities? (No partial points.) Force Acceleration Weight…

A: Concept: 1) Vector quantity has both magnitude and direction. 2) Scalar quantity has only…

Q: Determine the maximum mass (kg) that can be lifted at E if the 8-HP motor A has a maximum rotation…

Q: The velocity of water and pressure at the suction side of a pump is 4m/s and 90kPa respectively. If…

Q: S A- Sección 4-a 1200 N B 1500 N 1000 N

Q: . A steel ball [c-0.46 kJ/kg C, k-35 W/m. C] 5.0 cm in diameter and initially at a uniform…

Q: A spherical tank of diameter 4 m is half-full of water (weight density = 9800 N/m3). Setup the…

Q: 4. Find the horizontal force F to keep the gate closed. The gate is 2 m wide and 1.5 m in height.…

A: The horizontal force required to keep the gate closed: F = 7.63 kN

Q: 30° 6m P u8 А 8 There is an inclined beam supporting a concentrated load of P= 876 kN. Determine its…

A: According to the details provided in the question, we need to calculate the horizontal reaction at…

Q: a rubber ball is dropped into a concrete floor from a height of 2m. it rebounds to a height of 1.6…

A: Given dataA rubber ball is dropped.Initial height = 2 mRebound height = 1.6 mWe have to find the…

Q: Steam turbine receives 400000 kg/hr of steam throttled in actual reheat Rankine cycle with two…

Q: The weight of one dozen apples is 3.6 lb. Determine the average mass of one apple in both SI and US…

Q: The following creep data were taken on an aluminum alloy at 480 C (900 F) and a constant stress of…

A: Given: Time (min) Strain 0 0 2 0.22 4 0.34 6 0.41 8 0.48 10 0.55 12 0.62 14 0.68…

Q: The surface tension of the water in air in approximately 0.0756 N/m. If the atmospheric pressure is…

A: It is very basic question of fluid mechanics portion. Topic- Surface tension Used concept is…

Q: A two-stage air compressor with perfect intercooling takes in air at 1 bar pressure and 27°C. The…

A: We have a two-stage air compressor with flawless intercooling that takes in air at 1 bar and 27…

Q: A flat circular steel plate has a diameter of 50 cm and a mass of 60 kg. Calculate the thickness…

Q: Completely solve and box the final answer. Write legibly Determine the maximum mass (kg) can be…

Q: A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the…

Q: Consider the flow of water in the pipe system shown. Neglect minor losses. Which of the following…

Q: H.W₂ Sow at • A Power transistor for which TJmax = 180°c Can dissipat- a case temperature of so°c.…

Q: Determine the overall heat loss and the temperature profile at each interface of the following…

Q: e tapered beam supports a uniform distributed load w. If it is made from a plate and has a constant…

A: we have to determine the maximum stress

Q: The motion of an object is described by the v-t diagram shown below. What is the acceleration of the…

Q: A tianium disk (roe 107 CPa, Poisson's ratio = 0,34) precisely 8 mm thick by 30 mm diameter is used…

Q: A pipe has a diameter of 100 mm at section AA and a diameter of 50 mm at section BB. The velocity of…

Q: Find the Natural frequency of the system.

Q: A glass tube with a 90o bend is open at both ends. It is inserted into a flowing stream of oil (sp.…

Q: A diesel engine operating on the air- standard diesel cycle has six cylinders of 100 mm bore and 120…

A: Diesel Cycle is a type of constant pressure heat addition cycle and it consists of 4 processes:-…

Q: Consider a series of pipes as shown in the figure below that carries a discharge of 100 of water.…

Q: The weight of one dozen apples is 2.9 lb. Determine the average mass of one apple in both SI and US…

Q: of Appendix D as needed. spacec equal

A: we have to determine the distance where the two forces become equal

Q: 3. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414…

Q: Which of the following simulations can be done as a rigid-body analysis? O 1) Checking whether a…

A: W can answer the first question since the exact one is not specified. Please resubmit the question…

Q: Consider a regenerative cycle utilizing steam as the working fluid. Steam leaves the boiler and…

Q: Q1\ R22 compressed at Isentropic compression s=c, from P=0.3MPa & x-1, to P=0.7MPa, find enthalpy &…

Q: Determine the moment of inertia for shaded area about x and y axis. у 60 mm 30 mm MATHalino.com 45…

Q: The motor unit A is used to elevate the 300-kg cylinder at a constant rate of 2 m/s. If the power…

Q: What is truss

A: This question is based on the concept of trust in mechanical engineering.

Q: Inside Outside Length Heating Diamete Diamete Surface r r 56 cm 62 cm 273 cm 58 mm 64 mm 298 cm 58…

Q: A pump is locate bove the surface or a expels a jet tically upward a distance of 50ft. If 0.5cfs is…

Concept explainers

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.

Question

Do fast and accurate

A 27m3 CUBICAL TANK IS FULL OF TWO DIFFERENT FLUIDS OF EQUAL PARTS. AN
OBJECT WAS THROWN AND WAS PARTIALLY SUBMERGED PROJECTING 15%
ABOVE THE FLUID SURFACE. IF THE HEIGHT OF THE OBJECT IS 3m AND THE
SPECIFIC GRAVITY OF THE FLUIDS ARE 0.9 AND 0.82, FIND THE SPECIFIC
GRAVITY OF THE OBJECT. *
Your answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Principle of Floatation.

VIEW

Step 2 Calculation of specific gravity of the object.

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 7-cm diameter solid aluminum ball (SG = 2.70) and a 3.8-cm diameter solid brass ball (SG = 8.50) balance nicely when submerged in a fluid as shown in the figure. What is the specific gravity of the fluid? Neglect the friction on the pulleys. Please only round off on the final answer. Use three decimal places.
Make an explanation for every solution. and please be clear with your numerical solution. Problem: A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure.
When submerged in a fluid, a 7-cm diameter solid aluminum ball (SG = 2.70) and a 3.8-cm diameter solid brass ball (SG = 8.50) balance nicely, as seen in the image. What is the fluid's specific gravity? Neglect the friction on the pulleys.
At the surface of a freshwater spring, a manatee with a small amount of air in its lungs is neutrally buoyant. The manatee now dives to a depth of 10 m. At this greater depth, the buoyant force isA. Less than the weight force.B. The same as the weight force.C. Greater than the weight force.
Solve Correctly A cylinder object is suspended in a liquid at a distance of 38cm below the surface. The diameter of the object is 140cm and the density of the object is 960 kg/m3. The density ratio is 1. Determine the height of the cylinder, if the buoyant force is 7N.
A bottle consists of a cylinder 30 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting water vapor pressure, what is the depth to wich the open end is submerged below the free surface? a.30 cm b.60 cm c.50 cm d.none of the above
A cubical tank is 3 m x 3 m x 3 m and is layered with1 meter of fl uid of specifi c gravity 1.0, 1 meter of fl uid withSG = 0.9, and 1 meter of fl uid with SG= 0.8. Neglectatmospheric pressure. Find ( a ) the hydrostatic force on thebottom and ( b ) the force on a side panel.
Consider the slanted plate AB of length L in Fig. .( a ) Is the hydrostatic force F on the plate equal to theweight of the missing water above the plate? If not, correctthis hypothesis. Neglect the atmosphere. ( b ) Can a “missingwater” theory be generalized to curved surfaces of this type?
A closed cylindrical tank 2m in diameter and 8m deep with axis vertical contains 6m deep of oil (SG =0.8). The air above the liquid surface has a pressure of 0.8 kg/cm2. Determine the total force and location of it from the bottom of the tank?
Calculate the depth of the center of pressure for vertical rectangular plate having a height h = 10ft and base b = 5ft, and submerged in a liquid with its base at the liquid surface. If the upper base of the vertical rectangular plate given in the example problem is submerged by 12ft below the water surface, determine the location of the hydrostatic force and center of pressure. Answer should be (53,040 lbf and 17.4902ft)
A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure and detailed solution.
A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure. Please be clear and write explanation in every solution. Thank you.