A reinforced concrete column contains longitudinal steel equal to 1 per cent of net cross-sectional area of the column. Assume modular ratio as 10. The loads carried (using the elastic theory) by the longitudinal steel and the net area of concrete, are P and P. respectively. The ratio PJP. expressed as per cent is

A reinforced concrete column contains longitudinal steel equal to 1 per cent of net cross-sectional area of the column. Assume modular ratio as 10. The loads carried (using the elastic theory) by the longitudinal steel and the net area of concrete, are P and P. respectively. The ratio PJP. expressed as per cent is

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN
A 6m simply supported beam has a width of 330 mm and an effectivedepth of 520 mm. The yield strength of steel is 280MPa and thecompressive of strength concrete is 26MPa. The compression steel, if necessary,should be reinforced at d’ = 80 mm. Determine the required area of steelreinforcement for the following factored moment:a. Mu = 90 kNm b. Mu = 430 kNm c. Mu = 850 kNm
A rectangular beam has a width of 285 mm and an effective depth of 520mm. It is reinforced with 4 – 36 mm ø bars having fy = 430 MPa. If he compressivestrength of the concrete is 28MPa, find the following a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?
circular concrete pillar consists of 6 steel rods of 22mm diameter each reinforced into it. Determine the diameter of pillar required when it has to carry a load of 1000 kN. Take allowable stresses for steel and concrete as 140MPa and 8MPa respectively. The modular ratio is 15
A rectangular reinforced concrete beam has a length of 14 m is simply supported atboth ends. The width of beam is 350mm and the overall depth is 550 mm. Determine the area of the steel reinforcements if the beam is to carry a DL = 15kN/m and LL =18kN/m. The concrete strength fc = 25 and steel yield fy = 400 ��. Use 60 mm concretecover.
plz, solve all the parts of this problem. Use ACI code and Solve what you have been asked. Reinforced Concrete Design-1 A fixed ended beam with span length of 24′ and cross-section of 15ʺ x 24ʺ is subjected to uniformly distributed load is shown in figure 1. Unform service dead load is 1k/ft and uniform service live load is 1.4 k/ft. Taking ?c = 3?si and ?y = 40???, a) Analyze the beam for flexure only. b) Calculate the amount of reinforcement for the given demand and check for ductility requirements. c) Detail the reinforcement using #6 bar only, and also curtail the steel ensuring development length requirements. d) Show all your calculations in the form of neat and clean drafting. Note: Your drafting must include dimensional details, reinforcement details in both longitudinal and sectional views, and cut off locations of steel.
A rectangular pretensioned concrete beam is to be designed to carry superimposed dead and live loads of 300 plf and 1,000 plf, respectively, on a 40-ft simple span Straight tendons will be used. Time-dependent losses will be approximately 16 percent of the initial stress in the steel. Determine the concrete dimensions (use h = 2.5b ) and required prestress force and eccentricity, based on ACI limit stresses Concrete strength xi' = 5000 psi and f ci ^ prime =4,000 psi. 16 and service lis
A rectangular beam having a width of 300 mm has an effective depth of 600 mm. The totaldepth of beam is 680 mm. The beam is reinforced with 3-32 mm at the bottom. f c ’ = 27.6 MPa, and fy =415 MPa. Determine the following:1. The shear strength of concrete subjected to shear and flexure only if it is subjected to afactored moment Mu = 134 kN.m which occurs simultaneously with Vu = 223 kN. 2. The shear strength of concrete if the beam is subjected to an axial compressive force of268 kN. 3. The spacing of 10 mm shear reinforcement if the simple beam has a span of 6 m andsupports a factored uniform load of 150 kN/m including its own weight.
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the distance of the neutral axis from the extreme compression concrete? A. 139.51 mm B. 151.93 mm C. 118.58 mm D. 188.15 mm
1. A rectangular reinforced concrete beam has a length of 7.5 – 10.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.
*Subject: Reinforced prestressed concrete - Civil Engineering *Please refer for my attached formula or guidelines solve this problem A one-way both ends continuous slab is to support the moments tabulated. Consider L= 5m. Fc’ = 21MPa and fy = 415MPa. Dead load Moments: +42KN.m at midspan ;-67KN.m at support; Live Load Moment: +40KN .m at midspan; -44KN.m at support. Determine the spacing of the temperature bars.
A reinforced concrete beam has a width of 325mm. and a total depth of 450 mm. It has an effective depth of 375 mm and isreinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa. a. Determine thedepth of the compression blockb. Determine thetotal compressive force of concretec. Determine theultimate moment capacity of the beam