einforced concrete beam has a width of 325 mm. and a total depth of 450 mm. It has an effective depth of 375 mm and is reinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa. a. Determine the depth of the compression block

einforced concrete beam has a width of 325 mm. and a total depth of 450 mm. It has an effective depth of 375 mm and is reinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa. a. Determine the depth of the compression block

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam of length 702mm has a width of 132mm and a depth of301mm. Compression steel bars are placed at a distance 98 mm from the extreme concrete compressivefiber. The beam supports service dead loads of dead load (16 KN/m) and live load (24 KN/m). Reinforced with 4 25mm tension steel bars and 4 12mm tension steel bars f′c = 42 MPafy = 519 MPa 1. Solve for the height of the neutral axis measured from the extreme compression fiber.2. Solve for the design moment.3. Solve for the strength reduction factor.
Determine the prestressing force required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f =11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm A=103125 mm2 Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam.
A short rectangular column 300 mm along x-axis and 400 mm along y-axis. It isreinforced with 8-20-mm-diameter longitudinal bars equally distributed to the shortersides of the column. The centroid of the bars are 76 mm from the concretesurface. Use f’c = 21 MPa and fy = 415 MPa. 6.Determine the compressive force on steel bars in the compression zone at balanced condition with bending about y-axis.
4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa a. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = ____ mm (2 decimal places) b. What is the condition of failure? = ____ (Balanced, Tension controlled, Compression controlled, Transition) c. Calculate the design moment strength of a typical interior beam. = ____ kN⋅m (whole number)
2. A reinforced concrete beam having a width of 280 mm and a total depth of 600 mm isreinforced for tension at the bottom with 6 - 36 mmɸ bars placed on two layers, 4 bars onfirst layer and 2 bars on second layer. Compute the effective depth of the beam and theclear horizontal spacing between bars.
A rectangular reinforced concrete beam with width of 350 mm and effective depth of 600 mm is subjected to 250 Kn.m bending moment. the beam is reinforced with 6-25 mm bars. Use alternate design method and modular ratio, n = 10. a. find the location of the neutral axis from the bottom of the beam & moment of Inertia. b. Find the maximum stress of concrete and steel c. total compression force in concrete?
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
A rectangular concrete beam 400 mm wide and effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f'c= 21 MPa and steel yield strength fy = 275 MPa.a. Determine the depth of the rectangular compression stress block.b. Determine the ultimate moment capacity of the beam.
A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 4-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 24 MPa and rebar strength fy = 280 MPa. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. (A to D) Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. (E to H) Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight. (I to L) A. 44.15 B. 78.85 C. 57.34 D. 98.56 E. 195.66 F. 89.60 G. 133.91 H. 110.15 I. 16.31 J. 39.16 K. 26.16 L. 20.51
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is subjected to a nominal moment of 550 kN-m. If fc = 28 MPa, fy = 280 MPa, and Es = 200 GPa. a. Determine the balance steel ratio in percent; b. Solve for the depth of the equivalent rectangular stress block; c. Check whether the beam is tension-controlled, compression-controlled, or within the transition region and determine the value of the strength reduction factor, ; d.Solve for the ultimate moment capacity of the beam.
A doubly reinforced concrete beam has a max. effective depth of 630mm and is subjected to a factored moment of 1062 kn-m (including its own weight). fºc=27.58 MPa, fy = 413.4 MPa. Use 62.5 mm steel covering. 1. Determine the width of the beam. 2. Determine the reinforcement for compression. 3. Determine the reinforcement for tension.
A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. 1. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. 2. Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. 3. Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight.