A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a = 22.0 x 10-6/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) OB (2) P = 45 KN 2,100 mm 1

A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a = 22.0 x 10-6/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) OB (2) P = 45 KN 2,100 mm 1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Similar questions

A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A copper wire 2.0 m long, hanging vertically, supports a load of 6.0 kN.Neglecting the weight of the wire, determine the required diameter ifthe stress is not to exceed 300 MPa and the total elongation is not toexceed 5.0 mm. Assume E = 125 GPa.Answer: d = ___________________
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3950 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 2.0 m, x2 = 3.0 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.3125 in. The average shear stress in the pin cannot exceed 45 ksi, and the bearing stress in the pulley support bracket cannot exceed 65 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
A steel bar ABCD consists of three sections: AB is of 20 mm diameter and 200 mm long, BC is 25 mm square and 400 mm long, and CD is of 12 mm diameter and 200 mm long. The bar is subjected to an axial compressive load which induces a stress of 30 MN/m 2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E -- 210GN/m 2. [0.272 mm.] Could you please answer this fully? If you use * can you explain whatyou mean by it. Thank you
A steel bar AD has a cross sectional area of 300mm^2 and loaded by a force P1=15kN, P2=10kN, and P3=8kN. The lengths of the segments are a=2.0m, b=0.6m, and c=0.90m. E=200GPa. a. Determine the change in length of the bar. b. determine the stress of member BC. c. By what amount should the load P3 be incresed so that the bar does not change in length when the three loads are applied?
As shown in the figure, when the temperature was 24 ° C, a 0.5 mm gap was left. Determine the approximate value (° C) of the required temperature so that the normal stress in the aluminum bar is 75 MPa.