Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN Current Attempt in ProgressTwo solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm? and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1= 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowablenormal stress.A(1)BAnswer: PmaxkN

Consider the diagram as shown below for the given system.

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Answer: Pmax = Enter your answer in accordance to the question statement kN

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Answer: Pmax = Enter your answer in accordance to the question statement kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4350 mm2 and an allowable normal stress of 130 MPa. Bar (2) has a cross-sectional area of A2 = 4550 mm2 and an allowable normal stress of 80 MPa. Assume x1 = 2.2 m, x2 = 2.9 m, y1 = 1.3 m, and y2 = 2.6 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips.Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
Present FBD 1. A flat bar of width b = 60mm and thickness t=10mm is loaded in tension by a force P. The bar is attached to a support by a pin of diameter d that passes through a hole in the bar of the same size. If the allowable normal stress = 140MPa, shear stress is 80MPa and bearing stress is 200MPa, what is the diameter of the hole for which P is maximum? What is the value of P?