(b) A roller bearing having a bore of 160 mm, an outside diameter of 340 mm and a value of C of 1.32 MN has been selected to carry a load of 200 kN at 260 rev/min. The lubricant has a viscosity of 40 c.St at 37.8 °C. The required life is 286 x 106 revolutions. Calculate the reliability % of the bearing.

(b) A roller bearing having a bore of 160 mm, an outside diameter of 340 mm and a value of C of 1.32 MN has been selected to carry a load of 200 kN at 260 rev/min. The lubricant has a viscosity of 40 c.St at 37.8 °C. The required life is 286 x 106 revolutions. Calculate the reliability % of the bearing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A natural feed journal bearing of diameter 50mm and length 50mm operating at 20rev/s. Carries a load of 2KN. The lubricant used has a viscosity of 20MPa. The radial clearance is 50um. The Sommerfeld number for the bearing?
You are asked to design a plain surface journal bearing to carry a steady radial load of 5.75 kN while the shaft rotates at 950 rpm. The shaft stress analysis determines that an acceptable nominal diameter of the journal is 62.5-mm and an l/d ratio is 1. The shaft is part of a machine requiring good precision. So a minimum radial clearance cmin= 0.040 mm seems appropriate. We shall use SAE 30 oil as a lubricant, at an inlet temperature of 45 oC. Analyze the hypothetical bearing,a) Determine the operating temperature Tave, and operating viscosity μave. b) Determine the minimum film thickness, ho, temperature rise of the lubricant, ΔTC, the total oil flow, Q, and side flow Qs in [mm3/s], the maximum film pressure Pmaxdeveloped in [MPa]. c) Determine the power loss, Hloss in [W], friction torque, Tf in [N-m] d) For minimum radial clearances, perform a design assessment using Trumpler’s criteria.
A full journal bearing has a nominal diameter of 60.0 mm, a bearing length of 30.0 mm and supports a load of 3200 N when running at the design speed of 3200 rpm. The radial clearance has been specified as 0.04 mm. An SAE 20 oil has been chosen and the lubricant supply system is capable of delivering the lubricant to the bearing at 60oC. Using the Raimondi and Body design charts;1.1 find the temperature rise of the lubricant, (19)1.2 the total flow rate required, (1)1.3 the torque required to overcome friction (3)1.4 and the power dissipated in the bearing.
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A 2.5 in diameter by 1.8 in long journal bearing is to carry 5000 lb load at 320 rpm using SAE 40 lube oil at 200 oF through a single hole at 30 psi. Compute the bearing pressure. A. 1111.11 psi B. 142.23 psi C. 123.34 psi D. 197.34 psi Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
A wet disk clutch is to be designed to transmit 150 Nm of torque at 1200 rpm using 4 pairsof sintered lining with a maximum pressure at 1.8 N/mm² and the coefficient of friction as0.06. Assume uniform wear, compute the following:i.The required inner and outer diameters of the sintered lining if the internal diametershould be 0.577 of the external diameter.ii.The number of disks needed.iii.The power transmitting capacity.iv.The axial force exerted by the springs to keep the clutch engaged.
Please Full Answer A) 1) Explain two Types of bearing 2) Explain about Absolute viscosity, kinematic viscosity and SUS 3) Explain 3 types of lubrication occurs in bearings B) Select a deep-groove ball bearing for a radial load of 600 1b, an axial load of 150 1b, and inner race rotation. An L10 life of 180 million revolutions is desired. Reliability factor KR = 1.0; Shaft rotation factor V= 1.0; FaoverCo = 0.028
Whqt are Rigid Bodies? Give at least 5 examples with description.
A full journal bearing has a journal diameter of 25 mm, with a unilateral tolerance of -0.03 mm. The bushing bore has a diameter of 25.03 mm and a unilateral tolerance of 0.04 mm. The 1/d ratio is 1/2. The load is 1.2 kN and the journal runs at 1100 rev/min. If the average viscos- ity is 55 mPa • s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Using bolts of the same material and cross-sectional area, two possible attachments for a cylinder head are shown. Compare the strain energy developed in each case, and then explain which design is better for resisting an axial shock or impact load
Q A thick-walled cylinder has an inside diameter of 150mm. The inside of the cylinder is subjected to an internal fluid pressure of 350bar and the external pressure being zero. The fluid has a nominal density of 785kgm-3 and a viscosity of 36mPas. a) Find to the nearest mm the outside diameter required if the maximum stress of the material is 400 MNm-2 and a safety factor of 3 is required. b) Plot the stress distributions through the wall.