You are asked to design a plain surface journal bearing to carry a steady radial loadof 5.25 kN while the shaft rotates at 1080 rpm. The shaft stress analysis+0.000determines that an acceptable diameter of the journal is ds62.5*-0.050 mm, abushing with a diameter dn = 62.6+0.100-0.000 mm, and an l/d ratio is 1.. We shall useSAE 40 oil as a lubricant, at an inlet temperature of 45 °C. The shaft is part of amachine requiring good precision, so for a minimum radial clearance (Cmin) analyzethe hypothetical bearing,c)Determine the power loss, Hloss in [W], friction torque, Trin [N-m]d)For minimum radial clearances, perform a design assessment using Trumpler's

Answered: Image /qna-images/answer/9abb5450-ca15-4bc6-83f3-264e1ab016eb.jpg

You are asked to design a plain surface journal bearing to carry a steady radial load of 5.25 kN while the shaft rotates at 1080 rpm. The shaft stress analysis determines that an acceptable diameter of the journal is ds = 62.5±0.008 mm, a %| bushing with a diameter dn = 62.6±0:308 mm, and an l/d ratio is 1.. We shall use %3D SAE 40 oil as a lubricant, at an inlet temperature of 45 °C. The shaft is part of a machine requiring good precision, so for a minimum radial clearance (Cmin) analyze the hypothetical bearing,

You are asked to design a plain surface journal bearing to carry a steady radial load of 5.25 kN while the shaft rotates at 1080 rpm. The shaft stress analysis determines that an acceptable diameter of the journal is ds = 62.5±0.008 mm, a %| bushing with a diameter dn = 62.6±0:308 mm, and an l/d ratio is 1.. We shall use %3D SAE 40 oil as a lubricant, at an inlet temperature of 45 °C. The shaft is part of a machine requiring good precision, so for a minimum radial clearance (Cmin) analyze the hypothetical bearing,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The material of a certain transmission shaft uses AISI 1030 HR, its yield strength is 260 MPa, the transmission torque of this shaft is 160 N·m, and it is subjected to a uniform axial tension of 0.5 kN. Please calculate according to the Distortion energy theory. The minimum shaft diameter with a safety factor n of 2.5 (to 2 decimal places).
A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in simple tension test at a stress of 150 MPa. The shaft was subjected by bending moment and torque which are 22.2 kNm and 44.4 kNm respectively. Calculate the minimum allowable shaft diameter, d according to:- (a) Tresca failure criterion (b) Von Mises theory of elastic failure
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A conical pivot bearing 150 mm in diameter has a cone angle of 120º. If the shaft supports an axial load of 20 kN and the coefficient of friction is 0.03, find the power lost in friction when the shaft rotates at 200 r.p.m., assuming 1. Uniform pressure, and 2. uniform wear. [Ans. 727.5 W ; 545.6 W]
A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm respectively and transmits 8000 kW at 100 r/min. If this shaft is connected to a similar shaft, 1 m long, through a 10-bolt rigid flange coupling, determine the minimum standard bolt diameter if the pitch circle diameter of the coupling is pcd = 450 mm and the allowable shear stress in the bolts should not exceed 55 MPa.1.Determine the equivalent torsional stiffness of the shaft assembly.
A 2-in-diameter C1118, as rolled steel shaft rotates at 240 rpm. Assuming a repeated, reversed and gradual loading is applied, determine the maximum horsepower that can be transmitted (hp). Since torsional stress is considered a shearing stress, use the equation Ssy = 0.75 Sy for the design. find, Horsepower, hp
What length of a square key is required for a 5-in diameter shaft transmitting 1000 hp at 1000 rpm? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively.
A steel rotating-beam test specimen has an ultimate strength of 1600 MPa. Estimate the life of the specimenif it is tested at a completely reversed stress amplitude of 900 MPa.
The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the gear on the shaft is 0.9 kg, dimension, surface and notch factors KbK / Kç = 0.83, shaft speed n = 1120 rpm, shaft transmitted power 7.5 kW, force on shaft Fn = F = 2680 N Since the desired safety coefficient is Ssafe = 2; Check the safety of the shaft
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.
A solid steel shaft, 90 mm in diameter is coupled in series to a hollow shaft withan external diameter of 100 mm and internal diameter of 90 mm. Calculate thetorsional stiffness of 1 mm length of each of these shafts if they are usedseparately and compare this with the torsional stiffness of a 1 m length of thecompound shaft consisting of a 0.5 m length of each of the shafts mentionedabove. (G = 80 GPa)