solve show solutions A rope is wrapped over a 6 cm diameter pipe to support a bucket of tools. The coefficientof friction between the rope and the pipe is 0.20. The combined mass of the bucket andthe tools is 100 kg.a.) What force "F" is being applied to the free end of the rope if the bucket of tools ison the verge of being "lifted" by this force?b.) What force "F" is being applied to the free end of the rope if the bucket of tools ison the verge of being "lowered" by this force?μ = 0.2020°bucket100 kgr-3 cmAns.Part a.) 1440 NPart b.) 668 N

Step 1:Diameter is 6cmCoefficient of friction is 0.2The mass of the bucket is 100kgAngle of the pipe…

Answered: A rope is wrapped over a 6 cm diameter…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 A dustbin of mass 12 kg standing on horizontal ground is pushed by a horizontal force of 40 N. If the coefficient of friction is 0.4, will the dustbin move?
In a simple machine, an effort of 100 Newton lifts a load of 840 Newton. if the distance moved by the effort is 20cm and that by load is 2 cm,find: (i) Mechanical advantage (ii) Velocity ratio (iii) Efficiency (iv) Effort lost in friction (v) friction in terms of load
A 60-lb wooden box is pushed a distance of 50 ft on a horizontal stone floor by a force just sufficient to overcome the friction between box and floor. The coefficient of kinetic friction is 0.40.(a) What is the required force?(b) How much work does the force do?
A box of mass 12 kg standing on horizontal ground is pushed by a horizontal force of 30 N. If the coefficient of friction is 0.25, will the box move?
When a car brakes hard and skids, the maximum deceleration is 6 m/s2. The coefficient of friction between tires and road is _____.
1. On October 9,1992, a 27-pound meteorite struck a car in Peekskill,NY,creating a dent about 22cm deep. If the initial speed of the meteorite was 550m/s, what was the avarage force exerted on the meteorite by the car?(a) Solve in Newton Law.(B)Work-Kinetic Theorem.(C)Conservation Law.
A 11120 N car is designed with a 310 cm wheelbase. The center of gravity is located 60 cm above the pavement and 105 cm behind the front axle. If the coefficient of road adhesion is 0.6, what is the maximum tractive effort that can be developed if the car is (a) front-wheel drive and (b) rear-wheel drive? (c) how far back from the front axle would the center of gravity have to be to ensure that the maximum tractive effort developed for front- and rear-wheel drive options is equal?
A person is pushing two boxes placed side by side with each other. What is the acceleration caused by the applied force if the net force is 253.22, the coefficient of kinetic friction of the boxes is 0.74 and the sum of the mass of the boxes is 91.05kg? Is it possible to have one of the boxes generate an applied force of 144.34N, if yes, what is the mass of the other box?
A hydraulic press has a ram of 30 cm diameter and a plunger of 2cm diameter. it is used for lifting a weight of 30 kN. How much force is required at the plunger? a) 155.5kN b)466.6kN c) 311.1 kN d) 233.3 kN
A pull of 20 N at 30° to the horizontal is necesary to move a block of wood on a horizontal table. If the coefficient of friction between the bodies in contact is 0.25, what is the weight of the block?
.A flywheel rim which weighs 822 pounds has a mean diameter of 44 inches. The speed is to be maintained between 90 and 130 rpm. Calculate capacity of the flywheel in ft-lbf. Assume density of rim material as 7250 kg/m3. (Hint: Be careful of units and divide the answer by g=32.2 ft/s2 to obtain ft-lbf)
2.) An automobile lift raises a car weighing 3000 lbf, 6 ft off the shop floor (Fig. 2-12). Assuming the lift itself weighs 500 lbf and that friction is negligible, what is the work necessary to raise the car in ft-Ibf and m-N ?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS