A saturated clay stratum of thickness 10 m, bounded on top and bottom by medium coarse sand layers, has a coefficient of consolidation of 0.002 cm2/s. If this stratum is subjected to loading, it is likely that it would undergo 50% of its primary consolidation in:

A saturated clay stratum of thickness 10 m, bounded on top and bottom by medium coarse sand layers, has a coefficient of consolidation of 0.002 cm2/s. If this stratum is subjected to loading, it is likely that it would undergo 50% of its primary consolidation in:

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.12P

See similar textbooks

Related questions

Q: What is the value of the reaction at the right support in kN?

Q: A rigid bar AB is supported by a spring as shown in the figure above. What is the deflection of the…

Q: An open, 1-m-diameter tank contains water to a depth of 1.1 m when at rest. If the tank is rotated…

Q: Design a bracket connection to support an end reaction of 200 kN. The. eccentricity of the load is…

Q: 3. Explain why use chemicals is required in water treatment 4. Give the reasons why settlement in a…

A: To find:- We have to draw reference of use of chemicals in water treatment. We also have to draw…

Q: Determine the stiffness matrix and load vector for the following Frame Structure. P ton Lm K=EI P…

Q: A conical vessel is 12 m across the top and 15 m deep. If it contains water to a depth of 10 m, find…

Q: Determine the slope of the curve x2 + y2 – 6x + 10y + 5 = 0 at the point (1,0). 1/5

Q: SITUATION. A uniform ladder 3 m long weighs 200 N. It is placed against a wall making an angle of 60…

Q: A retaining wall 9 m high, with its back face smooth and vertical. It retains sand with its surface…

Q: 150. kN.m 25. kV/m C B 1m Im 4m R1 R2 FIGURE B

Q: SITUATION. A uniform ladder 3 m long weighs 200 N. It is placed against a wall making an angle of 60…

Q: use force method Consider the beam shown below. The structure is subjected to two concentrated…

Q: 1.1 how to use a level 1.[Calculation] To calculate the elevation of some points, a leveling route…

A: surveying : The technique, profession, art, and science of identifying the two-dimensional or…

Q: Consider a regime channel having a discharge of 50 m3/s and silt factor 1.10. The hydraulic radius…

Q: Find the angle between the planes 4x - y + 8z = 9 and x+ 3y +z = 4. %3D 72.45 107.55 17.55 162.45

Q: The 1052-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 475…

Q: agrams for the beam shown below. 10 kN p= 20 kN/m

Q: What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars…

Q: A1 m long steel rod has a cross sectional area of 100 sqm. It is Elasticity modulus is 200 000 MPa.…

Q: a) Determine the unit hydrograph for Gilmore Creek from the observed runoff (note: the area of the…

A: Solution For finding the unit hydrograph first find the Direct runoff hydrograph(DRH). For DRH,…

Q: 8. Compute the AL and the Ad for each leg of the traverse shown below. Show the EL and the Ed as…

A: Lattitude and departure signs : N-E : Both positive S-E : Lattitude negative Departure positive…

Q: Calculate the depth h of mud for which the 3-m concrete retaining wall is on the verge of tipping…

Q: Examine the diagram to the right. Calculate the tension in the rope. a) 5N b) ON ) 49.05 N c) 9.81 N…

A: Given data : The value of mass of block m=5 kg The value of acceleration due to gravity g=9.81 m/s2…

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

Q: 1. Assume that a town has proposed to abstract water for supply from nearby river. Outline the data…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: D.JF Ihe allowable benoliny stresses in tim ber and oteel are 8 ind 140MPA respectively, find tle…

Q: Q2) The figure shows a cantilever consisting of steel channel size 127 mm×64 mm. Using…

A: Answer We know that the Superposition principle says that the effect of combined loading is equal…

Q: A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this…

Q: Determine the value of EIv (in lb ft3 )at midspan for the beam loaded by two concentrated forces if…

Q: A glass (SG = 2.6) is filled to a depth d with linseed oil (SG=0.92) and allowed to float in a tank…

Q: Fnd all rea < tions Pin Structur Use Consistent de formation metho d [: Gustant اسئلة حلول

Q: AW18× 40 standard steel shape is used to support the loads shown on the beam. Assume P = 28 kips, w…

A: step 1-

Q: ar a body completely submerged in a fluid, the center of gravity )are known. The body is considered…

Q: A 15 cm length of steel rod with relative density of 7.4 is submerged in a two layer fluid. The…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 740 mm.…

A: Determination of largest moment M

Q: Tank ruptures OR Overpressure Wall fatigue failure AND Excessive Relief temperature valve fails gure…

A: Fault tree diagram helps in easy understanding of any problem In the above fault tree diagram we…

Q: A conical vessel is 12 m across the top and 15 m deep. If it contains water to a depth of 10 m, find…

Q: Given the Frame as shown below with weight 'W' for the smaller member and weight '2W' for the larger…

Q: Choose one type of space truss structure for a 100m span hangar and a 30m span gas station (both are…

A: Selection of roof trusses are mainly done on the basis of suitability of truss for the particular…

Q: A square section tank of 10FT side and 7FT length as shown has the top of one side wall in the shape…

Q: A horizontal water jet with a velocity of 10 m/s and cross-sectional area of 10 mm2 strikes a flat…

A: given-velocity v=10m/sarea A=10mm2density ρ=1000 kg/m3

Q: Consider the beam shown below. The structure is subjected to two concentrated loads. If all three…

A: we have a beam in the question where two concentrated loads are there we have to find out the…

Q: A layered soil is shown with the corresponding values K1, K2, and K3. Compute the equivalent…

Q: AV-notch weir is located or cut at one end of a tank having a horizontal square section by 12 m. The…

A: The given data is: Horizontal square section 12 m*12 m The head on the weir=1.50 m Time taken for…

Q: choose the countable nouns only* J shelf J fruit J blood J Gold I went to the zoo ago a week." true…

A: three different questions are given regarding English grammar

Q: In a consolidation test, the void ratio of the specimen which was 1.068 under the effective pressure…

A: Given data, Initial void ratio eo = 1.068 Final void ratio ef = 0.994 Initial pressure = 214 kPa…

Q: 3. What is the value of the reaction r1 in kN?

Q: SITUATION. A 250 x 300 mm concrete beam is prestressed with a pre-stressing force of 530 kN at an…

A: Given: b= 250mm, d= 300mm, P = 530KN, eccentricity = 60 mm and superimposed load = 50KN/m

Q: K F 40 mm 120 mm C 40 mm A 100 mm 240 mm- K

Concept explainers

Calculation of Settlement

The vertical displacement of the structural foundation due to the loading from the superstructure is known as settlement. It is due to the reduction of air voids present in the soil. The amount of vertical displacement depends on the bearing capacity of the soil on which the foundation is laid. The effect of the settlement depends on the magnitude of settlement, uniformity, and the structural design of the structure. The maximum allowable settlement for residential and office buildings should be less than 18 mm, for industrial buildings, it is 38 mm and for commercial buildings, it is 25 mm.

Question

A saturated clay stratum of thickness 10 m,
bounded on top and bottom by medium coarse
sand layers, has a coefficient of consolidation of
0.002 cm2/s. If this stratum is subjected to loading,
it is likely that it would undergo 50% of its primary
consolidation in:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

From the application of given pressure, the anticipated primary consolidation settlement is 0.064 mm. What is the average degree of consolidation for the clay layer when the settlement is 0.02 mm?
For a clay layer with Tv value of 0.05 find the average degree of consolidation for the whole layer and the percent consolidation at depth ratios 0, 0.5, 1, 1.5 and 2.
For normally consolidated clay layer in the field, the ff. values are given: Thickness of clay layer = 8.5ft, Void Ratio = 0.8; Compression Index = 0.28; Average effective pressure on the clay layer is 2650 lb/ft2; ∆σ = 970 lb/ft2; Secondary Compression index = 0.02. What is the total consolidation settlement of the clay layer five years after the completion of primary consolidation settlement? Time for completion of primary settlement = 1.5 years)
A 3.0 m thick singly drained normally consolidated claylayer has eo =0.89, Cc = 0.46, and cv =3.5 m2/year. Theeffective overburden pressure at the middle of the layeris 105.0 kN/m2. It is proposed to build a large warehousethat is expected to impose a pressure of 50.0 kN/m2 at theground level. What would the primary consolidation settlement be?
A clay layer consolidates after 6 years when its thickness is 5.70 m and the void ratio is 1.08. Assuming the secondary compression index in 0.04, estimate the secondary compression settlement in the next 15 years. Express your answer in mm rounded to the nearest whole number.
coefficient of consolidation of 20 ft2 /yr is given for the singly-drained clay layer. This layer is subjected to a uniform vertical stress increase of 100 kPa.2 years after the application of the load what will be the value of the excess pore pressure at point A . chart giving the local degree of consolidation.
If a saturated layer has a unit weight of 125 pcf, what is the submerged unit weight?What is the degree of consolidation of the abovementioned soil?
A 3 meter thick clay layer (pore water flowing in both directions) saturated with water loaded with embankment soil underwent 90% primary consolidation within 150 days. Determine the coefficient of consolidation of the clay for a certain pressure range.
A normally consolidated clay layer, 3 m thick, has the following properties : Initial void ratio, e0= 0.8 Compression index, Cc = 0.25 Average effective pressure, σ’0 = 125 Kpa Expected pressure increase, Δσ’ = 45 Kpa Secondary compression index, Ca = 0.02 Time of completion of primary settlement = 1.5 years What is the total settlement of the clay layer five years after the completion of the primary settlement?
A normally consolidated clay layer has the following properties: Soil layer thickness: 3.7 m Initial void ratio: 0.63Compression index: 0.29 Average effective pressure: 133 kPa Expected pressure increase: 58.7 kPa Secondary compression index: 0.02 Time for completion of primary settlement: 3 yearsa. Determine the void ratio at the start of the secondary consolidation. b. What is the total settlement of the clay layer 9 years after the start of primary consolidation settlement?
A normally consolidated clay layer, 4m thick, has the following properties:Initial void ration, eo = 0.65Compression Index, Cc = 0.20Average effective pressure, σ’o = 100 kPaExpected pressure increase due to loading on ground surface = 30 kPaSecondary compression index, Cα = 0.02Time for completion of primary settlement = 1.5 yearsWhat is the total settlement of the clay layer five years after the completion of primary consolidation settlement?
For an over-consolidated clay deposit, the pre-consolidation pressure is 120 kN/m2, and the overburden pressure is 80 kN/m2. The over-consolidation ratio of the deposit is