A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the figure below. In the power cycle, steam (water) with a mass flow rate m, enters the turbine at state 1. A portion of the steam (m₂) exits the turbine at state 2 before passing through the mixing chamber. The remainder (m3 = 3 kg/s) exits the turbine at state 3 and then enters a heat exchanger where it is cooled by the refrigeration cycle. The water leaves the heat exchanger at state 4 as a saturated liquid and then is pumped up to the mixing chamber pressure. R-134a with a mass flow rate of me is used in the refrigeration cycle to provide cooling to the water in the heat exchanger. Properties at each state are given in the figure below. Assume that the compressor, turbine, pump, mixing chamber, throttling valve and outer walls of the heat exchanger are well insulated and neglect changes in potential and kinetic energy across all devices.

A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the figure below. In the power cycle, steam (water) with a mass flow rate m, enters the turbine at state 1. A portion of the steam (m₂) exits the turbine at state 2 before passing through the mixing chamber. The remainder (m3 = 3 kg/s) exits the turbine at state 3 and then enters a heat exchanger where it is cooled by the refrigeration cycle. The water leaves the heat exchanger at state 4 as a saturated liquid and then is pumped up to the mixing chamber pressure. R-134a with a mass flow rate of me is used in the refrigeration cycle to provide cooling to the water in the heat exchanger. Properties at each state are given in the figure below. Assume that the compressor, turbine, pump, mixing chamber, throttling valve and outer walls of the heat exchanger are well insulated and neglect changes in potential and kinetic energy across all devices.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.46P

See similar textbooks

Similar questions

The operating condition for the single compressor in a household refrigerator is the lowest box temperature, which is typically A. 0F B. -20F C. 20F D. 40F
The figure below shows a vapor power cycle that provides process heat and produces power. The steam generator produces vapor at 500 lbf/in.2, 800°F, at a rate of 8 x 104 lb/h. Eighty-eight percent of the steam expands through the turbine to 10 lbf/in.2 and the remainder is directed to the heat exchanger. Saturated liquid exits the heat exchanger at 500 lbf/in.2 and passes through a trap before entering the condenser at 10 lbf/in.2Saturated liquid exits the condenser at 10 lbf/in.2 and is pumped to 500 lbf/in.2 before entering the steam generator. The turbine and pump have isentropic efficiencies of 85% and 89%, respectively. For the process heat exchanger, assume the temperature at which heat transfer occurs is 465°F. Let T0 = 60°F, p0 = 14.7 lbf/in.2 Determine:(a) the magnitude of the process heat production rate, in Btu/h.(b) the magnitude of the rate of exergy output, in Btu/h, as net work.(c) the rate of exergy transfer, in Btu/h, to the working fluid passing through the steam…
The above refrigeration system uses R-12 as the refrigerant, determine: 1. Enthalpies at each point of the cycle 2. Total mass of refrigerant that circulates the system in kg/s 3. Total refrigerating capacity in TOR 4. Total compressor power in kW 5. Heat rejected in kW 6. Coefficient of Performance 7. Draw the P-h Diagram Note: Show your SYSTEM BALANCING.
The figure below shows a vapor power cycle that provides process heat and produces power. The steam generator produces vapor at 500 lbf/in.2, 800°F, at a rate of 8 x 104 lb/h. Fifty-two percent of the steam expands through the turbine to 10 lbf/in.2 and the remainder is directed to the heat exchanger. Saturated liquid exits the heat exchanger at 500 lbf/in.2 and passes through a trap before entering the condenser at 10 lbf/in.2Saturated liquid exits the condenser at 10 lbf/in.2 and is pumped to 500 lbf/in.2 before entering the steam generator. The turbine and pump have isentropic efficiencies of 85% and 89%, respectively. For the process heat exchanger, assume the temperature at which heat transfer occurs is 465°F. Let T0 = 60°F, p0 = 14.7 lbf/in.2 Determine:(a) the magnitude of the process heat production rate, in Btu/h.(b) the magnitude of the rate of exergy output, in Btu/h, as net work.(c) the rate of exergy transfer, in Btu/h, to the working fluid passing through the steam…
A steam-powered power plant works on the basic Rankine cycle.shown in the figure. Likewise, some of its thermodynamic states are summarized in the attached table.Knowing that the work per unit mass delivered to the pump is 3W4 = 2480 (J/kg], determinein SI units the following: a) The specific volume of water in state 4.b) The associated work per unit mass, developed in the Curbina.c) The associated heat per unit mass released by the water in the condenser.d) The efficiency of the cycle
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: d) The work generated by the turbine; e) The condenser heat rejection rate (Q H); f) The coefficient of performance of the cycle.
In a steam power plant that operates based on a Rankine cycle, the operating pressures of the steam generator and the condenser are 10,000 and 10 kPa, respectively. If the turbine inlet stream is saturated vapor and the condenser outlet flow is saturated liquid, determine the specific heat transfers in the steam generator and the condenser, the specific work involved in the turbine and the pump, and the thermal efficiency and the BWR of the cycle. Also, if the power plant produces 250 MW power, determine the mass flow rate of the cycle’s working fluid.
Using the energy balance equation, derive that for a cycle of a closed system:
Find the mean effective pressure of the thermodynamic cycle shown in the figure below.
for a thermodynamic work cycle that uses two turbines consisting of a (low pressure turbine) and (high pressure turbine), make a schematic of a WATER PIPE steam generator that can be used.
Refrigerant 134a enters the compressor of a refrigerator as superheated vapor at 0.20 MPa and -5 ° C at a rate of 0.7 kg / s, and exits at 1.2 MPa and 70 ° C. The refrigerant is cooled in the condenser to 44 ° C and 1.15 ° C. MPa, and throttles at 0.2 MPa. Neglecting any heat transfer and any pressure drop in the connecting lines between the components, show the cycle on a Ts diagram with respect to the saturation lines, and determine (a) the rate of heat removal from the refrigerated space and the inlet power to the compressor, b) the isentropic efficiency of the compressor, c) the COP of the refrigerator, d) show the Ts and Ph diagrams with all points
Steam turbine receives steam at 9.5 MPa, 540°C and the condenser at 0.01 MPa. Steam are extracted at 3 MPa, 1.8 MPa, and 0.6 MPa. Determine the following: 1. Degree superheat at point 2 2. Quality of steam at point 4 3. Mass extracted in kg/hr for each feedwater open heater and the remaining mass that enters the condenser assuming 20,000 kg/hr of throttle flow 4. Work net in kW 5. Cycle thermal efficiency