A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radi, r, - 0.0480 m and r, - 0.140 m, respectively. (a) If a downward force of F,- 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d,- 0.192 m, through what distance d, would the other end move

A schematic of a homemade hydraulic jack is shown in the figure below, with cylindrical tube ends of different radi, r, - 0.0480 m and r, - 0.140 m, respectively. (a) If a downward force of F,- 16.0 N is applied to the end with the smaller radius, how much force F, would the jack exert on a car if it were sitting above the other end? (Enter the magnitude.) (b) If the smaller piston is pushed down a distance d,- 0.192 m, through what distance d, would the other end move

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 83PE: The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the...

See similar textbooks

Similar questions

Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Calculate Reynolds numbers for flow of trough (a) a nozzle a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when be nozzle is attached to hose. The flow rate through hose and nozzle is 0.500 L/s. Can flow in either possibly be laminar?
Could capillary action be used to move fluids in a "weightless" environment, such as in an orbiting space probe?
Suppose the master cylinder in a hydraulic system is at a greater height than the cylinder it is controlling. Explain how this affect the force produced at be cylinder that is being controlled.
What force must exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on a second cylinder? The master cylinder has a 2.00-cm diameter and second cylinder has 24.0-cm diameter.
Some have a density slightly less than that of water and must exert a force (swim) to stay submerged. What force must an 85.0-kg grouper exert to stay submerged salt water if its body density is 1015 kg/m3?
A dam is used to hold back a river. The dam has a height H=12m and a width W=10m . Assume that density of the water is p=1000kg/m3 . (a) Determine be net force on tie dam. (b) Why does the thickness of be dam increase with?
The pressure dam early in problems section increases with depth. Therefore, there is net torque on the dam. Find be net torque.
How would you determine the density of an irregularly shaped rock?
Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.00-cm diameter and the slave has a 24.0-cm diameter.
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.