A self-adjuster screw mechanism (star wheel)  can be positioned on either the left or the right side of the vehicle.

Q: In a rack and pinion steering system, what protects the rack from contamination? a. The inner…

A: A gear set converts the circular motion of the steering wheel into the linear motion necessary to…

Q: Explain briefly the Two-and Four-Wheel Tractors

A: 2WD tractors put more emphasis on the back tyres to maintain traction, resulting in reduced…

Q: Which of these trucks are driving?

A:

Q: What type of axle merely supports the vehicle load and provides a mounting place for the wheels?

A: Axles are very important parts of an automobile. These axels are used to supports the loads and…

Q: Find the correct statement with respect to balancing of rotating masses: a. Second mass is…

A: Balancing of mass is done in order to reduce the induced vibration during rotation of the machine.

Q: when the bottom of a control arm is toward the front of the car and the point turns in to meet the…

A: A trailing arm is a type of independent rear suspension which has the pivot axis precisely…

Q: Explain the Jog/shuttle mechanism.

A: The explanation about the Jog/shuttle is given as under.

Q: Draw front,top and side view for the given object

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: What occurs when a wheel hits a dip or hole and moves downward? a. Jounce b. Free length c.…

A: Given Data : Wheel

Q: While discussing the fail-safe function: Technician A says that the 4WS indicator light is…

A: The statement given by technician A is correct as when the fail-safe function that is when the any…

Q: The part (most likely to fail) in a parallelogram-type steering system is the ______.   a. idler…

A:

Q: A locomotive in which the driving wheels are connected to leading and trailing wheels is called as…

A: Given: A locomotive in which the driving wheels are connected to leading and trailing wheels is…

Q: Explain by drawing a figure the recovery or capsizing (overturning) situation of a boat in the water…

A: Capsizing when a boat or ship is turned on its side or it is upside down in the water then…

Q: A power-steering hose transmits fluid under pressure from the ___ to the ___ ___ ___ ?

A: Consider the diagram shown below for the power steering system, Power steering is used to assist…

Q: In steering effect, always the Active couple is considered for gyroscopic effect. Select one: True

A: in steering effect always the active couple is considered for gyroscopic effect  true  false

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: Technician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily…

A: A high torque for maintaining the bearing adjustment is required in the FWD vehicles and not the RWD…

Q: The simplest type of balance for weighing is the___________.

A: To balance the weight, there are multiple possible lever arrangement. One such example is shown…

Q: least possible mass of the flywheel

A: Given; For a certain engine having an average speed;N=1600 rpmFluctuation of KE per cycle is found…

Q: Draw the free body diagrams for each part in the figures below: Pedal Crank- Spindle -Chain ring

A:

Q: a. How much chain will move with one rotation of the peđals (front sprocket)? b. How many times will…

A: Radius of small gear , r1=2 cmRadius of larger gear , r2=5 cm Iarcone rotation of gear…

Q: - Low-speed shaft - Gearbox JI Rotor Hub- kel - High-speed shaft k2 Nacelle- Blade de

A: Solution

Q: Wind Turbine Gearbox & Brake

A: In a wind turbine, a gearbox is used to transfer rotational speed from a low-speed rotor to a…

Q: What is the point at which a machine has a tendency to grab a body part? a. Grip point  b. Point…

A: Solution:   The correct option with necessary explanation is given below:

Q: The clutch friction disc always rotates with the

A:

Q: А В C

A:

Q: gular acceleration of link BC

A: given   angular velocity = 2 rad/s  angular acceleration =  4 rad /s

Q: Describe how caster adjustment may be used to compensate for road crown.

A: There are many ways to adjust the caster angle which are used to compensate for road crown. These…

Q: Explain with neat diagram of Flat belt drives(any two) with applications.

A: Flat belt drives: Flat belt drives are used for large amount of power transmission. there is no…

Q: .1. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive system…

A: A chain-drive system an be aligned easier than a belt-drive system since the chain-drive system A.…

Q: 4 Wheel Steering(4WS) While discussing the fail-safe function: Technician A says that the 4WS…

A: Technician A is correct.

Q: The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__…

A: The four often utilized final drive designs for FWD cars are chain drive, hypoid gear, planetary…

Q: Explain the function of a flywheel from a crank effort diagram.

A: To find : function of a flywheel from a crank effort diagram.

Q: While discussing steering problems: Technician A says that a “jerky” steering wheel and a “clunking”…

A: Technician A is correct.

Q: normal reaction at rear wheel if it is rear- wheel driven car (N) O a. 13328 O b. 9996 O c. 8330 O…

A: Given:Mass center of the rear engine, m=1530 kgcoefficient of static friction, μ=0.5

Q: d. station wagons 5. What is used to control the movement of a vehicle as it goes around corners? a.…

A: To control the movement of vehicle at the corners

Q: Mobility of a triple crank mechanism is one O four O two three

A: Mobility of triple crank mechanism is one

Q: Parallelogram steering arrangements typically use a rack and pinion mechanism.  True  False

A: Parallelogram steering arrangements typically use a rack and pinion mechanism is a FALSE statement.

Q: The core of any suspension system is the ___

A: Given Data : Suspension system

Q: The following component in the Milling machine houses all power and driving mechanisms Select one: O…

A: Answer: (d) Knee. The knee is an unbending dark iron throwing that slides all over on the vertical…

Q: a. How fast your car was traveling immediately before the brakes were applied b. The time required…

A:

Q: On most vehicles, the automatic adjuster cablesor levers are ___.a. installed on the secondary…

A: Given Data : Automatic adjuster cables

Q: ladde

A: ax=14.01m/s^2

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Q: For the description of machine, mechanism, link and parts, ( _____) is correct. A.Parts is motion…

A: For a description of machine there  is requirement of frame which should have relative motive to…

Q: The sum of all unbalanced forces on the rotating shaft must be zero is called O tatic balancing O…

A: Static balancing involves the balancing of centrifugal forces of rotating masses.

Q: Transmission angle is the angle between and link of a four bar mechanism

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.