Solve the problem and show the formula used.Subject : Machine Design 1 • A shaft is acted upon by a torque that continuously varies from 2200to 6400 in-Ib. It has a diameter of 1.25" and a material's yield strengthof 63,000psi. Find the variable component of stress.

Answered: Image /qna-images/answer/cd0f4ff4-a04a-4b05-85ba-cd1d6b5dd2f4.jpg

Answered: A shaft is acted upon by a torque that…

A shaft is acted upon by a torque that continuously varies from 2200 to 6400 in-lb. It has a diameter of 1.25" and a material's yield strength of 63,000psi. Find the variable component of stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Stress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown...

A: Given Stress strain graph L =60.8 mm Diameter 15.8 mm to find Percentage elongation

Q: diameter of flanges r of recess of bolts 6. Ccach bolt

Q: What are the disruptive technologies , explain with the help of suitable example

A: On several fronts, a never-ending parade of new technology is taking place. Almost every advancement...

Q: 2.13: To provide natural draught, a chimney of height 16 m is used. Calculate, OThe draught in mm of...

Q: What is the kinetic energy of a 3-kilogram ball that is rolling at 2 meters per second?

A: Given data : Mass of ball =m Velocity of ball=V To find : Kinetic energy

Q: a material can absorb radiation, what aerospace material property is demonstrated

A: Radiation heat transfer is a process in which heat waves are released and then absorbed, reflecte...

Q: 1.Talk about Hooks law? And the applications?

A: Dear student, we are suppose to solve only one question. Please post other question as a separate qu...

Q: For the crank- slide mechanism. B slides 03 along 0203 link making 300mm stroke, as shown in Figure....

Q: Q1.5 (v6q9-52, Diesel) An ideal cycle has a compression ratio of 18 and a cutoff ratio of 1.5. Deter...

Q: Check stability of truss

Q: The shown picture is for 12-cylinder engine. The piston number 5 is connected to bearing denoted by

A: Piston 5 is connected to the bearing denoted by 10 on the crank shaft

Q: 13. The cylindrical container is filled with oil in the upper half with a specific gravity of 0.79 a...

A: Given:s1=0.79s2=1

Q: 1-A solid axial member which is made from three parts with different materials (sections 1,2, and 3)...

A: Section 1 Diameter, D1 = 30 mmSection 2 Diameter , D2 = 20 mmSection 3 Diameter, D3 = 25 mm

Q: The Diesel Opacity (Smoke Meter) Emissions Inspection procedure requires that the Certified Inspecto...

A: After reading the procedure manual, I found out that RPM (tac) probe and oil temperature probe both ...

Q: of degrees sm shown

Q: concentrated load of 20 kN at its free end shown in Fig. 3. Determine: i) ii) iii) The position of t...

A: Given Beam type = Overhanging Load on beam = 10 kN/m uniformly distributed and 20 kN at end. To fi...

Q: üiven- u= 35mls V = om/s t-5secs S-2

Q: The compression ratio of an air-standard Otto cycle is 7.5. P1 = 85 kPa and T1 = 32 Celsius at the s...

Q: Part A The 150 lb man bes against the cushion for which the coefficient of static fricton is , 05 He...

Q: What is the pressure at 61, 500 ft in SI.

Q: tween two cities 60mi apart take if, a. It's going downstream where the current is 3mph b. It's goin...

Q: What is the density of air in standard atmosphere at 38, 200 ft in SI.

Q: Sment č Drpm for

Q: ickness(mr = 25 x 10*E

Q: 9. The density of saturated vapor refrigerant -134a is expression in the form p= aT + bT + c, (where...

A: Given data:- T1= -15°C T2 = 60°C P1=164 kpa P2=1683kpa

Q: • The shaft whose torque varies from 2000in-lb to 6000in-lb has 1.5" diameter and a yield strength v...

Q: A refrigerator door of area 0.6 sq.m consists of 25 mm of insulation on top of a thin metal sheet. ...

A: given; →area(A)=0.6m2→insulation thickness(t)=25mm=0.025m→inside heat transfer coefficent (hi)=10w/m...

Q: The position of the neutral axis; The maximum tensile and compressive stresses; and The shear stress...

A: moment of inertia of channel section = 3.37500 x107 about neutral axis

Q: A projectile is fired with an initial velocity of 60 m/s upward at an angle of 30 degrees to the hor...

Q: Which of the following statements regarding the “Pre-Emission Inspection Check” Of a diesel powered ...

A: Given Data: Which of the following statements regarding the “Pre-Emission Inspection Check” Of a die...

Q: We have the following state space model: *1 = 4x1 – 16x2 + 10u1Uz *2 = 3x3 – 9uz y = 5x1u2 + 3x2u1 a...

Q: An engine undergoes the brake power testing in an brake rope dynamometer running at 8000 rpm and exp...

A: Given data: N=8000 rpmT=500 N.m Need to determine the brake power generated by the engine.

Q: 1. Knowing that the ultimate load for cable BD (diameter is 20 mm) is 110 kN and that a factor of sa...

Q: The angle plate is subjected to the two 250-N forces shown. It is desired to replace these forces by...

Q: Select one of the following bearing for the load conditions. Radial load, F,-: Axial load, F 1600 N,...

A: Given:Fr=3000 NFa=1600 NRPM=1000

Q: Find the velocity of flow in pipe in m/s.

A: Flow = area * velocity

Q: Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. I...

Q: . An open cylindrical tank 1 meter diameter contains water to a depth of 3.56m. If the tank is rotat...

Q: Which of the following mixtures of air is heaviest: 1) 50% dry air only 2) 2% water vapor + 98% dr...

A: Question:- Which of the following mixtures of air is heaviest? Options Available:- 1) 50% dry air ...

Q: Water (1 kg) at 20 °C is placed in contact with a 50 °C reservoir. After it equilibrates, it is plac...

A: Given data: m=1 kgT1=20°C=293 KT2=50°C=323 KT3=100°C=373 KCw=4.2 kJ/kg.K Need to determine the total...

Q: 4. For the Wheatstone Bridge network shown in Figure. a) Evaluate the Wheatstone Bridge network and ...

Q: 2. If P = 8 kN, determine the average shear stress in the pins at A, B and C. All pins are in double...

Q: 21. The inside dimensions of a 3500 Watt oven are shown below. How long would it take to heat the ov...

A: Dear student, it seems like there is some data mistake in the question because 1% efficiency is not ...

Q: A barometric condenser serves a steam turbine which is exhausting 2720 kg of steam per hour at a pre...

A: The above given question is related to the engineering thermodynamics and to calculate the solution ...

Q: concentrated load of 20 kN at its free end shown in Fig. 3. Determine: i) ii) iii) The position of t...

A: Given Overhanging beam of length = 4 m Loads = 10kN/m distributed over 3 m and 20 kN at overhanging...

Q: Water in a main pipe at street level is at a gauge pressure of 140 kPa and is moving with negligible...

Q: Explain the life cycle assessment methodology

A: Life cycle assessment : Life cycle assessment it is define as it is the factual analysis which is as...

Q: A flow-through electric water heater has a 22 kW electric heater inside an insulated 2.0-cm-diameter...

A: we have to determine the outlet temperature

Q: Knowing that, ignoring air resistance, an apple falling from a height h hits the ground when 2h If y...

A: Given Data

Concept explainers

Introduction to Engineering Design Process

The engineering design process is a set of steps that engineers follow to come up with a solution to a particular problem. The solution to the problem involves the designing of a product that can accomplish a certain task and can qualify certain criteria. The process of designing is completely different from that of the scientific method, that you may be familiar with. If the project utilizes the observations, and the experiments then the engineering design process must be followed. The diagram shows the steps of the engineering design process, and the table below describes each step in more detail:

Question

Solve the problem and show the formula used.

Subject : Machine Design 1

• A shaft is acted upon by a torque that continuously varies from 2200
to 6400 in-Ib. It has a diameter of 1.25" and a material's yield strength
of 63,000psi. Find the variable component of stress.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:

VIEW

Step 2:

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Basics of Mechanical Engineering Design and Design Process

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A spherical steel pressure vessel (diameter 500 mm, thickness 10 mm) is coated with brittle lacquer that cracks when the strain reaches 150 X 10~ (see figure). (a) What internal pressure p will cause the lacquer to develop cracks? (Assume E = 205 GPa and v = 0.30.) (b) If the strain is measured at 125 x 10-6, what is the internal pressure at that point?
A solid circular bar A BCD with fixed supports at ends A and D is acted upon by two equal and oppositely directed torques T0, as shown in the figure. The torques arc applied at points B and C each of which is located at distance x from one end of the bar. (The distance x may vary from zero to L/2.) For what distance x will the angle of twist at points B and C be a maximum? What is the corresponding angle of twist 0max?
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A hollow steel bar (G = 80 GPa ) is twisted by torques T (see figure). The twisting of the bar produces a maximum shear strain ymax= 640 x 10-6 rad. The bar has outside and inside diameters of 150 mm and 120 mm, respectively. Determine the maximum tensile strain in the bar. Determine the maximum tensile stress in the bar. What is the magnitude of the applied torques T?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A circular steel tube of length L = 1.0 m is loaded in torsion by torques T (see figure). (a) If the inner radius of the tube is r1= 45 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1(in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maxi mum permissible outer radius (r2)max?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.