The Diesel Opacity (Smoke Meter) Emissions Inspection procedure requires that the Certified Inspector use an approved diesel opacity (smoke meter) tester to check emissions at the tailpipe and that the following must also be hooked up during the test: 1,RPM (tach) probe and oil temperature probe. 2. Oil temperature probe only. 3. RPM (tach) probe only. 4. Camshaft postion senso

The Diesel Opacity (Smoke Meter) Emissions Inspection procedure requires that the Certified Inspector use an approved diesel opacity (smoke meter) tester to check emissions at the tailpipe and that the following must also be hooked up during the test: 1,RPM (tach) probe and oil temperature probe. 2. Oil temperature probe only. 3. RPM (tach) probe only. 4. Camshaft postion senso

Automotive Technology

7th Edition

ISBN:9781337794213

Author:ERJAVEC, Jack.

Publisher:ERJAVEC, Jack.

Chapter31: Fuel Injection System Diagnosis And Service

Section: Chapter Questions

Problem 1MC: Which of the following is the most likely cause of a lean condition during acceleration and cruising...

See similar textbooks

Similar questions

True or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.
True or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.
Complete the following statement about compression testing using the following words. Words: Accurate, All, Battery, Button, Comparison, Compression, Consistent, Cylinders, Four, Fuel,Gauges, Hole, Increase, Install, Observe, Reading, Recorded, Remote, Revolution, Screw-in, Spark,Starter, Test, Warm, Wide-open 1 Before conducting a __________ test, disable the ignition and the __________ injection system.Most manufacturers recommend that the engine be __________ when testing.2 Prop the throttle plate into a __________ position to allow an unrestricted amount of air to enterthe __________ during the test.3 Remove __________ of the engine’s __________ plugs.4 Connect a __________ starter button to the __________ system.5 Many types of compression __________ are available. The __________ type tends to be the most__________ and easiest to use.6 Carefully __________ the gauge into the spark plug __________ of the first cylinder.7 Connect a __________ charger to the car to allow the engine…
Answer the following questions on diagnostic trouble codes (DTCs) relating to engine management systems. What is P0119 the diagnostic trouble code (DTC) for? What system component sets the P0119 DTC? What system condition is required to set the P0119 DTC? What are the conditions required to run a P0119 DTC? Identify two (2) possible causes of the P0119 Code?
Describe the purpose of a manifold absolute pressure (MAP) sensor.
While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?
Technician A says that changes in engine load cause changes in hydraulic pressure inside the transmission. Technician B says that engine load is monitored by throttle pedal movement or by engine vacuum. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
cpi (Central Multiport injection) injectors are located in the lower half of the intake manifold. T F
Explain the benefits of dynamic testing of automatic transmission fluid
List and explain the function of three (3) types of exhaust systems that can be fitted on diesel engines. (20 - 30 words each)
answer the following questions on automatic transmission diagnositc trouble codes. Complete the following table for the conditions required to run a P0741 DTC. The monitor will run whenever the following DTCs are not present 'ECT (Engine coolant temperature) Transmission range TFT (Transmission fluid temperature): TFT sensor circuit 'ECT sensor circuit Turbine speed sensor circuit Intermediate shaft speed sensor circuit Output speed sensor circuit Shift solenoid valve SL1 circuit Shift solenoid valve SL2 circuit Shift solenoid valve SL3 circuit Shift solenoid valve S4 circuit Shift solenoid valve SR circuit Shift solenoid valve DSL circuit Electronic throttle system
A defective LAT sensor or circuit may cause the fol lowing problems, except. hard engine starting rich or lean air-fuel ratio improper converter clutch lockup reduced fuel economy