A shaft rotating at 200 r.p.m. drives another shaft at 300 r.p.m. and transmits 6 kW through a belt. The belt is 100 mm wide and 10 mm thick. The distance between the shafts is 4m. The smaller pulley is 0.5 m in diameter. Calculate the stress in the belt, if it is An open belt drive, and 2. A cross belt drive. (Take μ = 0.3)

A shaft rotating at 200 r.p.m. drives another shaft at 300 r.p.m. and transmits 6 kW through a belt. The belt is 100 mm wide and 10 mm thick. The distance between the shafts is 4m. The smaller pulley is 0.5 m in diameter. Calculate the stress in the belt, if it is An open belt drive, and 2. A cross belt drive. (Take μ = 0.3)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.2P

See similar textbooks

Similar questions

Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.
A 3/8 inch flat leather belt is 12 inch wide and is used on a 24 inch diameter pulley rotating at 600 rpm. The specific weight of the belt is 0.035 lb/in3. The angle of contact is 1500. If the coefficient of friction is 0.3 and the allowable stress is 300 psi, how much hp can it transmit?
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)
A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has the following standard dimensions: b x h x l = 8 mm x 7 mm x 18 mm. Calculate the stresses.
A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm. Calculate the diameter of the shaft if the allowable shear stress on the shaft is 45 MPa. The number of bolts connecting the two halves is six. The permissible tensile stress for the bolts is 76 MPa. The coefficient of friction between the coupling and the shaft surface may be taken as 0.3. Also, find the diameter of the bolt. Torque in Nm Diameter of shaft in mm Diameter of bolt in mm
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100mm from its support and has horizontal belts tension ratio being 2.5.if the shear stress is to limited to 80MPa while transmitting 45kW at 900 r. p. m. Find the shaft diameter if it is to be used for the input - output belts being on the same or opposite sides
Describe the failure of a hollow torque tube. Calculate the forces creating the failure
A solid steel shaft, whose Sy= 300 MPa and Su= 400 MPa, is used to transmit 3000 kW at 800 rpm. Determine its diameter.