In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA=20;TB-60; Tc-140;TD=40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates € 140 B 120 Output MININA ww D 40 Arm B 60 20 DOWN Input INSPI

In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA=20;TB-60; Tc-140;TD=40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates € 140 B 120 Output MININA ww D 40 Arm B 60 20 DOWN Input INSPI

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate
Figure shows an alicyclic gear train with the following details:A has 40 teeth external (fixed gear) ; B has 80 teeth internal ; C - D is a compound wheel having 20 and 50 teeth (external) respectively, E-F is a compound wheel having 20 and 40 teeth (external) respectively, and G has 90 teeth (external). The arm runs at 100 r.p.m. in clockwise direction. Determine the speeds for gears C, E, and B.
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.
An epicyclic gear shown in the figure, if gear A is fixed. Determine the speed reduction between the input and the output shafts If the input shaft rotates clockwise when viewed from the right end, what is the direction of rotation of the output shaft? BSs1 Cs0 A50 s
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise.a) By calculating gear sizes; Draw in 1:1 scale.
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
2) Two mating internal 10-pitch, spur gears have 16 and 86 teeth. Determine the center distance. 3) Two mating external 8-pitch, 20o , spur gears have 24 and 64 teeth. Determine the contact ratio. 4) Two mating 20°, 8-pitch, spur gears have 14 and 42 teeth. Will they interfere? 5) A pair of 20°, mild-steel gears are to be selected for an application where they need to transfer 5 hp. The pinion drives at 1800 rpm and the gear must rotate as close to 480 rpm as possible. Select a set of gears to accomplish this task. a) Determine a suitable diametral pitch and pressure angle. b) Use the required velocity ratio to iterate and determine appropriate number of teeth (confirm that these gears are commercially available). c) Calculate the pitch diameters and center distance.
An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the Centre of the ring gear at 20 rpm. If the gear A is fixed, Calculate the speed of planet gear.
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.