A shaft with diameter of d=1 in. is under the fully reversed torque T= + 5500 Ib-in. It was machined from steel having properties of Sy =%3D100 ksi and Sy = 80 ksi.(A) Find the corrected fatigue strength, Sm at 103 cycles & theendurance strength, Se at 10° cycles.(B) Estimate the fatigue life of the shaft.

The diameter of the shaft is d=1 in. The magnitude of torque is T=5500 lb·in. The ultimate strength…

A shaft with diameter of d=1 in. is under the fully reversed torque T = + 5500 lb-in. It was machined from steel having properties of Sy = 100 ksi and Sy = 80 ksi. (A) Find the corrected fatigue strength, Sm at 103 cycles & the endurance strength, Se at 10° cycles. (B) Estimate the fatigue life of the shaft.

A shaft with diameter of d=1 in. is under the fully reversed torque T = + 5500 lb-in. It was machined from steel having properties of Sy = 100 ksi and Sy = 80 ksi. (A) Find the corrected fatigue strength, Sm at 103 cycles & the endurance strength, Se at 10° cycles. (B) Estimate the fatigue life of the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the angle of twist of the above stating your answer in degrees?
(2) A diesel engine developing 1,850 hp at 105 rpm is used on a ship to drive the propeller. The shaft of the propeller is to be made of 3.5% per cent nickel steel, heat-treated, with an ultimate strength in tension of 130,000 psi, and an ultimate in shear about 70% of the ultimate in tension. Angular twist is limited to 1° in 20 diameters. (a) Using a design factor of 2, find the diameter of solid shaft required. (b) Using the same data, find the diameter of hollow shaft required if the outside diameter is twice the inside diameter. (c) What is the percentage of saving in weight by using the hollow shaft?
A hollow steel shaft 2304mm long is to be designed to transmit a torque of 28350 kJ. The shear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the length of the shaft is must not exceed 6 degrees. And the shear stress in the shaft must not exceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts
A 1 ½-in. shaft is made of AISI 1045 steel, as rolled with Sy=59 ksi. For N = 2, what reversed torque can the shaft sustain indefinitely? Assume Endurance Strength as 21050 psi.
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
A solid titanium alloy [G=114⁢ GPa] shaft that is 950 mm long will be subjected to a pure torque of T=195 N⋅m. Determine the minimum diameter required if the shear stress must not exceed 145 MPa and the angle of twist must not exceed 3°. Report both the maximum shear stress τ and the angle of twist φ at this minimum diameter. Based only on the requirement that the shear stress must not exceed 145 MPa, what is the minimum diameter of the shaft? dτ= mm Based only on the requirement that the angle of twist must not exceed 3°, what is the minimum diameter of the shaft? dφ= mm Determine the minimum diameter required. dmin= mm Determine the polar moment of inertia corresponding to the minimum diameter for the shaft. J= mm4 Determine the maximum shear stress at the minimum diameter. τmax= t MPa Determine the angle of twist in the shaft at the minimum diameter. Enter your answer in degrees. φ= °
A solid shaft 100 mm in diameter is subjected simultaneously to an axial compressive force of 600 kN and atorque that twist through an angle of 1.5o in a length of 8 m. if the modulus of rigidity is 80 000 MPa. What is maximum shear stress of the shaft?
A shaft in torsion only is to transmit 2500 hp at 570 rpm. Its material’s allowable shear stress is 10 ksi. (a) What should be the diameter of a solid shaft? (b) If the shaft is hollow, Do = 2Di, what size is required? (c) Which is the lighter? By what percentage? (d) Which shaft is the more rigid? PLEASE I NEED IT ASAP . THANK YOU
What reversing torque in N-mm, can a 38 mm shaft sustain if the yield strength and endurance strength is 244.14 MPa and 143.5 MPa respectively? Assume a factor of safety of 2.
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
Design of a Shaft subjected to Alternating Loads 1. [Proof of Concept] Considéra machined steel circular shaft subjected to maximum and minimum bending moment of 1000 and 4000 lb .in, respectively; and a maximum and minimum torque of 250 and 1600 Ib.in, respectively. Consider the factor of safety to be 2, the yield strength of the materials 40 ksi, and its ultimate strength to be 70ksi.Determine the minimum diameter of the shaft for the case where D is 20% larger than d, the fillet radius is 10% of d, and reliability is 99%. You may use DE-ASM E formula. 2. Write a computer code that can take Tm, Ta, Mm, Ma, choice of material, safety factor, and other necessary assumptions from the user and return an estimated diameter for the shaft.Choice of inputs is up to you. Note that many of the required quantities are themselves function of the shaft diameter. Your code should be submitted with a report.