Answered: A sheet of copper is stretched…

A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are εx = 0.40 x 10-3and εy = 0.30 x 10-3 ,determine δx and δy Use E = 110 GPa and v = 0.35.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.6P

See similar textbooks

Related questions

Q: 4. The control linkage of an airplane consists of a rigid member DBC and a flexible cable AB. A…

Q: If a horizontal load applied to the bar AC causes point A to be displaced to the right by an amount…

A: From the above figure length of the wire, LAB is calculated as:

Q: 1. The square plate is deformed as shown. Determine the normal and shear strains at E with respect…

A: GIVEN: TO FIND: The Normal and shear strain at E with respect to the X-Y and X'-Y' axis.

Q: A rod has a radius of 10 mm. If it is subjected to an axial load of 15 N such that the axial strain…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are εx = 0.40…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A: From triangle ABP, The expression to calculate the length of line AB is, Substitute values in the…

Q: A rod has a radius of 10 mm. If it is subjected to an axial load of 15 N such that the axial strain…

A: Given: The radius of the rod is R=10 mm The axial load on the rod is FX=15 N The axial strain in the…

Q: An air-filled rubber ball has a diameter of 6 in. If the air pressure within the ball is increased…

A: Given data :Initial diameter (di) = 6 inFinal diameter (df) = 7 in

Q: The rubber block is subjected to an elongation of 0.03 in. along the x axis, and its vertical faces…

A: Given: The elongation along x-axis, ∆L = 0.03 in The angle turned by vertical face, θ = 89.3⁰ The…

Q: The polysulfone block is glued at its top and bottom to the rigid plates. If a tangential force,…

A: GIVEN :-y=3.56x14TO DETERMINE :-the shear strain at the corners A and B,

Q: When the state of strain is represented by the principal strains, no shear strain will act on the…

A: Forces acting perpendicular to the cross section of the body are normal forces. They can be either…

Q: Prove that the sum of the normal strains in perpendicular directions is constant, i.e., P x+ P y = P…

A: Sum of strains in X and Y directions are Sum of strains in perpendicular X and Y directions are

Q: Determine the shear strain gxy at corners D and C if the plastic distorts as shown by the dashed…

A: The FBD of the system is as follows:

Q: The distributed loading is applied to the rigid beam, which is supported by the three bars. Each bar…

A: Due to the distributed load the bars will experience equal force. Let the force in each bar be F.…

Q: The load P produces an axial strain of –1,800 µɛ in post (2). Determine the axial strain in rod (1).…

Q: The material distorts into the dashed position shown, where d = 10 mm. d 2d D 50 mm B 200 mm EI 50…

Q: The A-36 steel bar consists of two segments, one ofcircular cross section of radius r, and one of…

A: The strain energy stored in circular section,

Q: The pin-connected rigid rods AB and BC are inclined at u = 30° when they are unloaded. When the…

Q: A rod has a radius of 10 mm. If it is subjected to an axial load of 15 N such that the axial strain…

Q: The wire AB is unstretched when u = 45°. If a load is applied to the bar AC, which causes u to…

Q: PROBLEM 1: If the applied force P causes the rigid arm ABC to rotate clockwise about pin A through…

A: Given: The rotation of arm ABC, θ = 0.04o

Q: If the force P causes the rigid arm ABC to rotate clockwise about pin A through an angle of 0.02°,…

A: Given data: Rotated angle, θ = 0.020 Drawing the rotation of the arm ABC: here, δB = displacement…

Q: The rod is subjected to the linearly varying axial distributed load as shown. What is the correct…

Q: The distributed loading is applied to the rigid beam, which is supported by the three bars. Each bar…

A: Given, Area of each rod = 1.25 in2 Load (w) = 25 kip/ft Now taking free body diagram of each…

Q: When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: Given Data: The length of the wire CD is L = 300 mm. The displacement of point B is s = 0.02 mm.…

Q: The strain at point A on the bracket has normal components 400x10-6 and 550x10-6 in x and y…

A: Given Data: strain at point A=∈x=400×10-6∈y=550×10-6 Vxy=-650×10-6

Q: he center portion of the rubber balloon has a diameter of d 100 mm. If the air lessure within it…

A: Given data : original diameter=100 mmfinal diameter=125 mm

Q: If the load P on the beam causes the end C to be displaced 10 mm downward, determine the normal…

A: Given Data: The displacement of point C under the load P is d= 10 mm. The length of cord BD and CE…

Q: The rigid body ABC is connected by two links and is exerted by force P as shown aside. If the normal…

Q: 2-1. An air-filled rubber ball has a diameter of 6 in. If the air pressure within it is increased…

Q: Prove that the sum of the normal strains in perpendicular directions is constant, i.e., Px + Py =…

A: Let strain in x and y directions are Px and Py respectively. strain in x` and y` directions are Px`…

Q: 3. Invert the plane stress form of Hooke's law and express the stress in terms of the strain…

A: Given data: poission's ratio=μElastic modulus=E Need to show the proof of given expressions.

Q: Show that the following strain components are the solutions of a problem in elasticity. E, = 2xy, E,…

Q: The bar DA is rigid and is originally held in the horizontal position when the weight W is supported…

A: First, draw the free body diagram of the system: Use the proportion to evaluate the value of δED:…

Q: The piece of plastic is originally rectangular. Determine the average normal strain that occurs…

A: The dimensions of the rectangular box are given as the:

Q: Indicate the points on the stress-strain diagram which represent the proportional limit and the…

A: The diagram shown is the stress-strain curve. It is developed using the UTM during the tensile…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are e, = 0.40…

A: Stress in x-direction, σx = 63.3 MPa. Stress in y-direction, σy = 55.2 MPa.

Q: The rigid body ABC is connected by two links and is exerted by force P as shown aside. If the normal…

Q: . A loading causes the member to deform into the dashed shape. Explain how to determine the normal…

Q: 2. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are Ex 0.40…

A: Given data: The strain in the x-direction is εx=0.4×10-3 The strain in the y-direction is…

Q: The material distorts into the dashed position shown. Determine the average normal strains along…

A: Draw the schematic diagram of the given fig.

Q: The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the…

Q: Determine the average normal strains in the two wires in Figure if the ringat A moves to A′.

Q: Determine the shear strain gxy at corners A and B if the plastic distorts as shown by the dashed…

A: Draw the figure representing the angles α, β, and ϕ.

Q: The aluminum rod AD (E=73 GPa, 0=23x10°6/°C) has a diameter of 15 mm and is attached to the rigid…

Q: 3. Each member of the truss is made of steel and has the cross-sectional area shown. Determine the…

A: Given Data: Young's Modulus E=200 Gpa=200×103Nmm2 Area of Trusses ACD=ACB=1500 mm2 and ABD=2000 mm2…

Q: The material distorts into the dashed position shown. Determine the average normal strains Px, Py…

A: Find out the normal strain in x-direction εx=A'F'-AFAF=150-150150=0 Find out the normal strain in…

Q: at A has coordinates (0, 0). If a load P acts on the ring at 3 becomes EAB = 0.02 in/in., and the…

A: data providedthe length of rod AB LAB = 5 in the length of rod Ac ,LAC = 8 in The normal…

Q: 6. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L…

Q: The bar has a length of 8 in. and a square cross-sectional area of 0.5 in. × 0.5 in. It is made of a…

Question

. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are
εx = 0.40 x 10-3and εy = 0.30 x 10-3
,determine δx and δy Use E = 110 GPa and v = 0.35.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are εx = 0.40 x10-3 and εy = 0.30 x 10-3, determine σx and σy. Use E= 110 GPa and v = 0.35.
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are epsilon_{x} = 0.40 * 10 ^ - 3 and epsilon_{y} = 0.30 * 10 ^ - 3 determine and Use sigma_{y}; E = 110 GPa and y = 0.35 . sigma_{x}. Use E= 110 GPa and v=0.35. Show complete free body diagram.
A rectangular titanium plate has the followingdimensions. a = 20 mm, b = 15 mm, and c=5 mm. Uniformly distributed tensile forces of 7.50 kN act in the z direction. Determine the strains in the x, y, and z directions. Let E = 120 GPa, and v = 0.35.
The state of strain at a point on a wrench has components ϵx = 120(10-6), ϵy = -180(10-6), γxy= 150(10-6). Use Mohr's circle to solve the problem. Determine the orientations of the element at which the principal strains occur. θp1= θp2=
Prove that the sum of the normal strains in perpendicular directions is constant, i.e., P x+ P y = P x + P y.
Prove that the sum of the normal strains in perpendicular directions is constant, i.e., Px + Py = Px′ + Py′
A sheet of steel is stretched biaxially in the xy-plane. The strains in the sheet are described below. Determine the stresses along the x and y axes. Use E=200 GPa and v=0.28 Ex = 0.4 x 10‐³ Ey = 0.3 x 10‐³
The normal stresses at a point in a steel member are σx = 8 ksi, σy = -4 ksi, and σz = 10 ksi. Using E = 29x103 ksi and ν=0.3, determine the normal strains at this point. a)Ex b)Ey c)Ey
2.Show that volumetric strain in a bar is equal to the sum of strains in three mutually perpendicular directions. 3. Explain the terms: (i) Modulus of elasticity (ii) Modulus of rigidity and (ii) Bulk modulus. 4. Derive the relationship between (i) Modulus of elasticity and modulus of rigidity (ii) Modulus of elasticity and bulk modulus
When the state of strain is represented by the principal strains, no shear strain will act on the element. True or False?
A rectangular aluminum plate of uniform thickness has a strain gauge at the center. It is placed in a test rig which can apply a biaxial force system along the edges of the plate as shown below. If the measured strains are +0.0005 and +0.001 in the x and y directions respectively, a) Determine the corresponding stresses set up in the plate and the strain through the thickness, εz. Take E=72 GPa and ν=0.32. b) Construct the Mohr’s circle for the loaded plate. c) State the values of the principal stresses. d) Determine the maximum shearing stresses and the directions of the planes on which they occur.
. The normal stresses at a point in a steel member are δx = 8 ksi, δy = -4 ksi and δz = 10 ksi. Using E = 29 x 103 ksi and v = 0.3, determine the normal strains at this point.