A short 3-4 transmission line with an impedance of (5 +j 20) O per phase has sending end and receiving end voltages of 46-85 kV and 33 kV respectively for some receiving end load at a p.f.of 0-8 lagging. Determine: (i) power output (ii) sending end power facto [(i) 22-86 kW (ii) 0-657 lag

A short 3-4 transmission line with an impedance of (5 +j 20) O per phase has sending end and receiving end voltages of 46-85 kV and 33 kV respectively for some receiving end load at a p.f.of 0-8 lagging. Determine: (i) power output (ii) sending end power facto [(i) 22-86 kW (ii) 0-657 lag

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.11P: A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of...

See similar textbooks

Related questions

Q: A 230-kV, three-phase transmission line has a per phase series impedance of z = 0.05 + j0.45 Ω per…

A: Given 230-kV z = 0.05 + j0.45 Ω per Km y = j3/4 × 10−6 siemens per km. It delivers 200 MVA, 0.8…

Q: A single-phase, 50 Hz, 120 km transmission line delivers 50 MVA at 0.86 lagging power factor at 132…

A: Nominal T- Network of a medium transmission line: Given: To find:

Q: A 230-kV, three-phase transmission line has a per phase series impedance of z = 0.05+j0.45 Ω per Km…

Q: 230 kV, three-phase transmission line has a per phase series impedance of z = (0. 05 + j0.45) ΩΩ per…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: Balance 3 phase system. Load is 30MW, 132kV at 0.85 PF lagging. Impedance of transmission line =…

Q: QUESTION 1: For the 3-ph, double circuit O.H.T.L shown below: 1- Find the spacing between the two…

A: According to question, For the 3-ph, double circuit O.H.T.L shown below: 1- Find the spacing between…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

Q: Answer the question in the below image. A short 3-o transmission line with an impedance of (5 + j…

Q: 1. A 69-kV (L-L), three-phase short transmission line is 16 km long. The line has a per phase series…

A: The solution is given below.

Q: 9.33 A three-phase, 60-Hz, 350-km transmission line has the following parameters: R 0.10 /km, XL at…

Q: A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a…

A: Percentage rise in voltage at receiving end is calculated as shown below

Q: A three-phase transmission line is 200 km long. It has a total series impedance of (25+ jl 10)2 per…

A: Given: A three-phase 200 km long transmission line has: Total series impedance, Z=(25+j110) Ω per…

Q: A load of 1000 kW at 0•8 power factor lagging is received at the end of a 3-phase line 20 km long.…

A: Given, Load:P=1000 kWpf =0.8 laggingZline=0.25+j0.28 per kmDistance of the line =20 kmTotal line…

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: The answer value given with the question is incorrect. The solution can be achieved as follows.

Q: À three phase 220KV, 50HZ transmission line supplies a power of 100MW at a power factor of 0.8 lag…

Q: A single phase short-transmission line is feeding a load of 12 kW at a 0.8 lagging power factor. The…

A: Given values are - PL=12kWcosϕ=0.8R=5ohmX=10ohmVL=440∠0oV

Q: The A and C constants of a medium length transmission line is 0.936 + j0.016 ohms and (-5.18 + j914)…

A: Basic problem on transmission line in power system.

Q: A balanced load of 30MW is supplied at 132 kV, 50Hz and 0.85 p.f. lagging by means of a transmission…

A: According to question: Using nominal 'T' approximation: The sending end voltage is calculated as…

Q: The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the…

A: Given data, Ir=988.1 ∠-68.6°Vr=400 kVZ=50+j200 Ω By using short transmission line equations,…

Q: A three-phase transmission line is 160 km long and supplies a load of 12 MW at 0.85 power factor…

A: i) Nominal T method- Total resistance, R=0.275*160 =44Ω Total inductive reactance, XL=0.5625*160…

Q: A 60 Hz, single-circuit, three-phase transmission line is 150 mi long. The line is connected to a…

Q: A 500-kV 60-Hz three phase transmission line is 463 km long. The series impedance is z=0.06+j0.4 Q…

Q: transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the…

Q: A 60-Hz, 230-km, three-phase overhead transmission line has a series impedance z = 0.8431/79.04°…

A: Overhead Power Line: An overhead power line is a structure that transmits electrical energy across…

Q: A 69-kV, three phase short transmission line is 16km long. The line has a per phase series impedance…

A: We need to determine the sending end voltage, voltage regulation, the sending end power, and…

Q: 230-kV (line-to-line), 50 Hz, three-phase transmission line has a per phase series impedance of z =…

A: In this question we will find ABCD parameters of line using nominal pi model...

Q: A single circuit, 60 Hz, three phase transmission line is "" long. The line is connected to a load…

Q: 1- Current through the line? 2- Sending end voltage? 3- Sending end power factor? 4- Regulation of…

Q: A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end…

A: The performance of a power system depends mainly on the performance of transmission lines in the…

Q: A 132 Kv, 50 Hz, 3-phase tensmission line delivers loaed of 5omw at 08 lagging Pf. 9, the…

A: For a 3-phase transmission line,Voltage, V=132kVFrequency, f=50HzPower, P=50MWPower factor,…

Q: The one line diagram of a four-bus system is shown to the right. The line impedances are given in…

A: Given V1 =1∠0° V3 =1.02P3 =0.9

Q: For the 3-ph, double circuit O.H.T.L shown below: 1- Find the spacing between the two conductors in…

A: According to the question, 1- Find the spacing between the two conductors in the double-bundle…

Q: single phase overhead transmission line delivers 4000 KW at 11KV 8.8 power factor lion if resistance…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The ABCD constants of a three-phase, 345-kV transmission line are A = D = 0.98182 + j0.0012447 B =…

A: In this question, The ABCD constants of a three-phase, 345-kV transmission line are A = D =…

Q: A 400 km long, 50 Hz transmission line having series resistance and inductance of 0.12/km and…

A: Given: A 400 km long, 50 Hz transmission line have Resistance, R=0.1 Ω/km Inductance, L=1 mH/km…

Q: For a given short transmission line of impedance R+jX ohms/phase, the sending end and receiving end…

A: Short transmission line Impedance Z=R+jX ohm/phase Sending end voltage Vs Receiving end voltages VR…

Q: A load of 4000 kW at 0•8 power factor lagging is received at the end of a 3-phase line 3 km long.…

Q: power of 90+j70 MVA is drawn from the end of a 220 km three-phase transmission line with a voltage…

Q: Draw a Lattice diagram each for transient currents and transient voltages that are propagating at…

A: Given data is shown below. V=1.25×108μsl=250mt=10μsVg=15∠10°Zg=145∠25°

Q: 2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: A 60Km cable serving a client on a PSTN was tested by the installation engineer during installation…

A: Given values are -

Q: Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines…

A: Given Conductor spacing = 7.25m P=125MW at 0.85pf lag

Q: A three phase line 30 km long delivers 2000 KVA at 33 kV voltage, 0.707 lagging power factor. If…

Q: A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end…

A: As given in the question

Q: A 230 kV transmission line has an impedance of 50 cis 78 ohms and a capacitive reactance of 1,200…

Q: Q) A transmission line of negligible loss has a characteristic impedance of 600 N. Calculate the…

Q: A short three phase transmission line of parameters R-0.4Ω and X=0.4Ω is delivering 2000kVA to a…

A: The transmission line performance can be determined by using four parameters namely series…

Q: Three-phase transmission line has ABCD constants as shown below. The line is 80 km long. A =…

A: The transmission line problem can be solved easily.

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A three-phase line with an impedance of (0.2+j1.0)/ phase feeds three balanced three-phase loads connected in parallel. Load 1: Absorbs a total of 150 kW and 120 kvar. Load 2: Delta connected with an impedance of (150j48)/phase. Load 3: 120 kVA at 0.6 PF leading. If the line-to-neutral voltage at the load end of the line is 2000 v (rms), determine the magnitude of the line-to-line voltage at the source end of the line.
(Q) A 10 mile transmission line with an impedance of (0.122+j0.849) Ω per mile is delivering 230A at 230kV and 0.8 power factor lagging. Determine: the sending end voltage the line efficiency and regulation
A short three phase transmission line of parameters R-0.4Ω and X=0.4Ω is delivering 2000kVA to a load at a pf of 0.8 lagging at the receiving enf=d of the line.if the load voltage is 3000 V, determine the voltage regulation and efficiency of the line.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
A three phase transmission line is 370 km long. The series impedance of the line is (0.294+ j0.724) Ω/km and the susceptance is (j6.17x e(-6)) S/km. The voltage at the sending end is 470 kV. (a)Find the sending end current and receiving end voltage when there is no load on the line. (b)Suppose a medium transmission line and determine the maximum permissible line length if the receiving end at no-voltage is not to exceed 430 kV.
transmission line with an impedance of 35 Ω is connected to a load of impedance of 300 Ω, then the value of VSWR assuming that the line impedance is decreased by 30 % and load impedance is increased by 40%.
A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admittance is 315 microsiemens. Shunt leakage may be neglected. Using the nominal T approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
For a given short transmission line of impedance R+jX ohms/phase, the sendingend and receiving end voltages Vs and Vr are fixed. Derive the expression for themaximum power that can be transmitted over the line.
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0.8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line.
A 46-kv 0.8-lagging power factor load is connected to the end of a short transmission line where the voltage is 230. If the line resistance and reactance are 0.06 and 0.08 ohm, respectively, calculate the voltage at the sending end.