The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R=radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m'; absolute viscosity (u) = 0.001 kg//m.s); Experimental data is shown as shown in the following table: Vavg (m/s) Ap (Pa) Task: a. Plot the graph of the pressure as a function of the average velocity (V.). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f= 2DAP PLIV. plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is formulated as Re =

The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R=radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m'; absolute viscosity (u) = 0.001 kg//m.s); Experimental data is shown as shown in the following table: Vavg (m/s) Ap (Pa) Task: a. Plot the graph of the pressure as a function of the average velocity (V.). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f= 2DAP PLIV. plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is formulated as Re =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When a clean glass tube with a diameter of 2 mm is immersed in water at 20 ° C, how many mm will the capillary rise occur in the glass tube? For water at 20 ° C, surface tension is given as 0.073 N / m, density 1000 kg / m3, contact angle 0 ° C and gravitational acceleration 10 m / s2.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
A pitot-static probe will be used to measure the velocitydistribution in a water tunnel at 20°C. The two pressurelines from the probe will be connected to a U-tube manometerthat uses a liquid of specifi c gravity 1.7. The maximumvelocity expected in the water tunnel is 2.3 m/s. Your job isto select an appropriate U-tube from a manufacturer thatsupplies manometers of heights 8, 12, 16, 24, and 36 in.The cost increases signifi cantly with manometer height.Which of these should you purchase?
Gasoline specific mass: 0,82 g/cm3Diameter 1 = 150mmDiameter 2 = 100mmCalculate the volumetric flow rate through a pipe, considering the results in:a) Bourdon Tubeb) Differential Manometers
In the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing through is measured with a U-tube manometer (Rm,1) as 10 cm (1stsituation). The manometer fluid is carbon tetrachloride(CCl4). Then, in order to avoid CCl4 poisoning, it is decided to add a layer of water to both arms of manometer (2nd situation). So, 4 cm of water is added to the left arm and 8 cm of water is added to right arm. In this newsituation, what will be the height difference of manometer fluid (CCl4) between the arms of the manometer (Rm,2)?Data: ρbenzene=876 kg/m3, ρwater=997 kg/m3, ρCCl4=1587 kg/m3
Using the data given in the schematic attached, find the difference of pressure PA and PB h1= 0.65m h2= 0.1m h3= 0.75m h4= 0.45m Density of fluid A is pA= 900kg/m3 Density of fluid B is pB= 1034kg/m3 Mercury density is pHg= 13600kg/m3 Oil density is poil= 700kg/m3 (In the given figure, the pipelines are parallel to each other and not necessarily at the same height.)
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.
Consider a soap bubble of diameter 3 mm. If the surfacetension coeffi cient is 0.072 N/m and external pressureis 0 Pa gage, what is the bubble’s internal gage pressure?( a ) - 24 Pa, ( b ) + 48 Pa, ( c ) + 96 Pa, ( d ) + 192 Pa,( e ) -192 Pa
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
When gage A indicates a pressure of 100 kPa gage, then cavitation just starts to occur in the venturi meter. If D = 40 cm and d = 10 cm, what is the water discharge in the system for this condition of incipient cavitation? The atmospheric pressure is 100 kPa gage, and the water temperature is 21°C. Neglect gravitational effects.
No wrong answer ..When 0.23 m³/s of water flows through a 300-mm diameter pipe, the level difference in a U-tube manometer, connected between two points, separated by 120 m, is 280 mm of mercury. What is the friction factor for the pipe?
PROB E. A capillary –tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum mass rate is 900 grams per hour. If the tube length is 10 cm and the maximum sustainable pressure is 25 Pa, determine the nominal diameter size of the tube to be used.