A simple pendulum is 0.42 m long. At t = 0 it is released from rest starting at an angle of 13°. Part A Ignoring friction, what will be the angular position of the pendulum at t = 0.35 s? Express your answer in degrees. ANSWER: Bo.35 = Part B Ignoring friction, what will be the angular position of the pendulum at t = 3.45 s? Express your answer in degrees. ANSWER: O3.45 = Part C Ignoring friction, what will be the angular position of the pendulum at t = 6.00 s? Express your answer in degrees. ANSWER: O6.00

A simple pendulum is 0.42 m long. At t = 0 it is released from rest starting at an angle of 13°. Part A Ignoring friction, what will be the angular position of the pendulum at t = 0.35 s? Express your answer in degrees. ANSWER: Bo.35 = Part B Ignoring friction, what will be the angular position of the pendulum at t = 3.45 s? Express your answer in degrees. ANSWER: O3.45 = Part C Ignoring friction, what will be the angular position of the pendulum at t = 6.00 s? Express your answer in degrees. ANSWER: O6.00

Classical Dynamics of Particles and Systems

5th Edition

ISBN:9780534408961

Author:Stephen T. Thornton, Jerry B. Marion

Publisher:Stephen T. Thornton, Jerry B. Marion

Chapter11: Dynamics Of Rigid Bodies

Section: Chapter Questions

Problem 11.30P

See similar textbooks

Similar questions

An 1150kg automobile has springs with k = 16,000N/m. One of the tires is not properly balanced; it has a little extra mass on one side compared to the other, causing the car to shake at certain speeds. If the tire radius is 42cm, at what speed will the wheel shake most? [Sketch the scenario first]
At what angular velocity will the stress of the rotating steelring equal 250 MPa if its mean radius is 220 mm? Thedensity of steel 7.85 Mg/m^3.
The wing of an aircraft is loaded by a torsional moment MT, creating a shear flow. What unit does the shear flow q have?
https://www.youtube.com/watch?v=6F6deDoKLoE During the lab, you fire the ballistic pendulum multiple times and find the average angle to be 46.7 degrees. If the length of the pendulum (from pivot to center of gravity) is 30.4 cm, to what height, h, did the pendulum's center of gravity rise? (Use the formula shown at 7:45 of the video) Give your answer in cm to 3 significant figures (2 decimal places in this case).
A particular human hair has a Young's modulus of 3.63×109 N/m2 and a diameter of 145 μm. If a 228 g object is suspended by the single strand of hair that is originally 20.0 cm long, by how much Δ? hairΔL hair will the hair stretch? If the same object were hung from an aluminum wire of the same dimensions as the hair, by how much Δ?AlΔLAl would the aluminum stretch? If the strand of hair is modeled as a spring, what is its spring constant ?hair?khair?
The largest tendon in the body, the Achilles tendon, connects the calf muscle to the heel bone of the foot. This tendon is typically 12.0 cm long, 5.30 mm in diameter, and has a Young's modulus of 1.65×109 Pa .If an athlete has stretched the tendon to a length of 12.7 cm, what is the tension ? , in newtons, in the tendon? ?= N
Find the Young’s modulus of the wire. (g= 9.81 m/s/s)
A 9 kg object's center of gravity lies at a point 16cm below the point of suspension. What is the frequency of vibration if it has a moment of inertia of 100kg⋅m2 ?
A 6 kg mass attached to a horizontal spring oscillates at a frequency of 9 Hz. At t =0 s, the mass is at x= 4.9 m and has vx =− 6.85 m/s. What is the angular frequency (?ω) in rad/s?
The 12m boom AB weighs 10 kN, the distance of the center of gravity being 6m from hinge A. For the position shown, determine the tension T in the cable BC and the reaction at hinge A.
You pull a simple pendulum 1.40 m long to the side through a small angle of 3.50º. What is the speed of the pendulum as it passes through equilibrium? Give your answer in m/s.
A solid disk of radius, R = 0.063 m, and mass, M= 0.500 kg, has a small hole drilled through it halfway between its center and outer edge and the disk is pinned to the wall through the hole so that it may rotate freely on the pin. a) Using a free-body diagram, with the weight of the disk acting at its centre of mass, determine the torque on the system about the axis and determine, using similar arguments as were used for a pendulum for the class notes, the constant k for the linear restoring torque in this case. b)The effective mass of the system will be the moment of inertia about the axis which you have already calculated above. Your work above should establish that the system executes SHM with the angle theta as the variable rather than the displacement, x, as was the case for the spring motion we studied in class. Use the similarity of this analogous system to follow the same steps as were used in class to get the angular frequency of a pendulum and determine the period that the…