A simple Rankine cycle uses water as the working fluid. Water enters the pump as a saturated liquid at 10 kPa and exits at a pressure of 5 MPa. Water enters the condenser as a saturated mixture with a quality of 90%. Assume that the cycle is ideal. QUESTION 1 What is the temperature of the turbine inlet, in °C? Report your result to one decimal place using rounding. QUESTION 2 What is the specific enthalpy at the pump outlet, in kJ/kg. Report your answer to two decimal places using rounding. QUESTION 3 How much heat was added in the boiler, in kJ/kg. Round to the nearest whole number.

A simple Rankine cycle uses water as the working fluid. Water enters the pump as a saturated liquid at 10 kPa and exits at a pressure of 5 MPa. Water enters the condenser as a saturated mixture with a quality of 90%. Assume that the cycle is ideal. QUESTION 1 What is the temperature of the turbine inlet, in °C? Report your result to one decimal place using rounding. QUESTION 2 What is the specific enthalpy at the pump outlet, in kJ/kg. Report your answer to two decimal places using rounding. QUESTION 3 How much heat was added in the boiler, in kJ/kg. Round to the nearest whole number.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure ratio of a Brayton cycle with an air-powered regenerator is 8. The lowest and highest temperatures of the cycle are 310 K and 1150 K. The adiabatic efficiencies of the compressor and turbine are 75% and 82%, respectively, and the regenerator efficiency is 65%. Show the cycle in the T-sdiagram. Consider the variation of specific heats with temperature. a) The temperature of the air at the exit of the turbine,b) The completion of the cycle,c) Calculate the thermal efficiency of the cycle.
Determine maximum temperature of the cycle for the given question
Completely solve and box the final answers. Write legibly In a steam turbine plant, a single bleed is taken from the turbine for regenerative feed water heating (closed). The inlet of the turbine is supplied with steam at 3.4 MPa and 320 C and exhausts at 0.15 MPa for bled steam. The remaining will expand which in turn exhausts at 0.01 MPa. The working fluid is throttled via throttle valve after the closed feed water heater going to the condenser. By drawing the system and showing the process on T-s diagram determine (a) the mass fraction of the bled steam, then (b) the work net and the thermal efficiency of the system.
1. Figure shows a reheat cycle in which steam is delivered to the high-pressure turbine at 1100 Ibf/in^2, 740 F, and expanded to 200 Ibf/in^2. After the expansion, the steam is warmed to 720 F before being expanded to 1 lbf/in^2 in the low- pressure turbine. Assume the turbines and pump are adiabatic. Compute the high pressure isentropic turbine work. High Q'în Boi ler Condenser Pump Q out 166.8 Btu/lbm 200.1 Btu/lbm 190.2 Btu/lbm 231.1 Btu/lbm 120.5 Btu/lbm
An ideal Brayton cycle has a pressure ratio of 8:1. The temperature of the air is 29 °C at the inlet to the compressor and 1080 °C at the inlet to the turbine. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific work input to the compressor to one decimal place and indicate the correct unit (JI..).
An ideal Brayton cycle has a pressure ratio of 6:1. The temperature of the air is 28 °C at the inlet to the compressor and 1,035 °C at the inlet to the turbine. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJkg K respectively. Calculate the specific work output to the turbine to one decimal place and indicate the correct unit (J/..).
1.) The ratio of the pressures in an Ericsson Cycle is 8. Determine the Thermal Efficiency in % 2.) The compression ratio of a Stirling Cycle is 11. What is the thermal efficiency in %? 3.) The compression ratio of a Stirling Cycle is 4. Heat is rejected at 90C. What is the highest temperature in the cycle in Celcius? ANSWER SHOULD BE ROUND OFF IN SIX SIGNIFICANT FIGURES
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 4. Calculate the total turbine work of the cycle.
Q2:A constant pressure heat addition air standard cycle af a compression ratio of (17.0) .Heat is added at a rate of (1500 kJ/kg) and the atmospheric conditions are (1.0 bar) and (35 °C). Show the cycle on both P-V &T-S diagrams and calculate : 1-the temperature and pressure at each point in the cycle. 2-the thermal efficiency 3-mean effective pressure. [take y=1.4,Cv=0.715 kJ/kg.k & R=0.287kJ/kg.k]
Read the questions carefully and answer with complete solution and units.Use the steam tables provided and use 4 decimal places for solving.Final answers shown are in 2 decimal places.Draw the T-S diagrams properly with respect to the saturation line. In an ideal Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.)Find the quality of the steam,Qa, Qr, Wt,Wp,Wnet,efficiency,and steam rate. Final Answers must be: 74.16% ,2894.58??/??, 1774.50??/??, 1130.17??/??, 10.09??/??, 1120.08??/??, 38.70%, 3.2141??/??ℎ
An iseal Brayton cycle has a pressure ratio of 6:1. The temperature of the air is 22 degrees celsius at the inlet to the compressor and 1080 derees celsius at the inlet to the turbine. Take specific heat at constant pressure and constant volume for air as 1,006 KJ/kg K and 0,717 KJ/kg K respectively. Calculate: 1. the compresion absolute temperature to one decimal place 2. the work ratio of the plant to three decimal places 3. the specific work output to the turbine and specific work input to the compressor , to one decimal place and SI unit 4. the thermal efficiency of the plant to one decimal place
44. The schematic diagrams of two suggested designs for a boiling water reactorare shown in the figures. One uses a direct cycle and the other a dual cycle. Theoutlet conditions for both designs are the same. In both designs, steam leaves thesteam separator assembly with a quality of 95% to enter the high pressure turbine(HPT) while the saturated liquid with 95 weight percent being recirculated to thereactor. The vapor is expanded successively in the HPT, the intermediate pressureturbine (IPT), and the low pressure turbine (LPT) before entering the condenserbeing at a 64 mm-Hg. Moisture separators between the HPT and IPT and betweenthe IPT and LPT reduce the steam moisture to 1%; the separated liquid is used toheat the feedwater in an open feedwater heater. The heated condensate and the recirculatedwater from the steam separator are pumped through the reactor. Assume100% efficiency in all pumps, and neglect pressure losses in the moistureseparators. Take all turbine efficiencies as…