solve part c Member ABC is controlled using a rack and pinion, which isconnected at B. (The rack is the long, horizontal gear.) The rackcan only move horizontally and the pinion does not translate. Ablock in a sleeve is connected at A and allows movement onlyin the vertical direction. Member ABC has a total length of2.40 m and the distance between A and B is 1.25 m. Whenmember ABC forms an angle of 0 = 37.0° with the rack, theacceleration of B is ag = 1.55 m/s² and the velocity of theblock attached at A is vA = 2.95 m/s in the direction shown.Positive angular velocity and acceleration are in thecounterclockwise direction. (Figure 1)Figure8aBB1 of 1SubmitCorrectPart B - Acceleration of CPrevious AnswersFind acceleration of C, ac, at the instant shown. Give your answer in component form.Express your two answers, separated by commas, to three significant figures in meters per second squared.► View Available Hint(s)ac = 2.98,-14.8 i j m/s²SubmitCorrectPrevious AnswersPart C - Acceleration of BaB =Find the acceleration of B when the acceleration of C is ac = 4.65 i+2.76 j m/s² and the acceleration of A isa = -3.00 j m/s². Member ABC makes an angle of 0 = 23.0° at the instant considered.Express your answer to three significant figures in meters per second squared.► View Available Hint(s)Submit17 ΑΣΦvecDrovido Foodbook?im/s²

Answered: Image /qna-images/answer/ae1fd1b2-e28b-489d-bdb0-554645f19f0a.jpg

Member ABC is controlled using a rack and pinion, which is connected at B. (The rack is the long, horizontal gear.) The rack can only move horizontally and the pinion does not translate. A block in a sleeve is connected at A and allows movement only in the vertical direction. Member ABC has a total length of 2.40 m and the distance between A and B is 1.25 m. When member ABC forms an angle of 0 = 37.0° with the rack, the acceleration of B is ag = 1.55 m/s² and the velocity of the block attached at A is A = 2.95 m/s in the direction shown. Positive angular velocity and acceleration are in the counterclockwise direction. (Figure 1)

Member ABC is controlled using a rack and pinion, which is connected at B. (The rack is the long, horizontal gear.) The rack can only move horizontally and the pinion does not translate. A block in a sleeve is connected at A and allows movement only in the vertical direction. Member ABC has a total length of 2.40 m and the distance between A and B is 1.25 m. When member ABC forms an angle of 0 = 37.0° with the rack, the acceleration of B is ag = 1.55 m/s² and the velocity of the block attached at A is A = 2.95 m/s in the direction shown. Positive angular velocity and acceleration are in the counterclockwise direction. (Figure 1)

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter46: Suspension Systems

Section: Chapter Questions

Problem 13RQ: The coil springs of the vehicle_. a. support the weight of the vehicle b. provide axle location c....

See similar textbooks

Similar questions

A four bar mechanism is made up of links of length 100,200,300 and 350 mm. if the 350 mm link is fixed, Claculate the number of links that can rotate fully.
In a four bar linkage mechanism the length of shortest and longest links are given as ‘a’ and ‘b’. The length of other two links are given as ‘c’ and ‘d’ respectively. Identify the Grashoff’s law equation from the following which guarantees the continuous relative motion between the links in the mechanism. a. b + d = a + c b. a + b < c + d c. a + c < b + d d. b + c < a + d
A mechanism to spray water onto vehicles at an automated car wash is shown. Classify the four bar mechanism, based on its possible motion, when the lengths of the link are: a = 12 in b= 1.5 in c= 14 in d= 4 in
Draw the free body diagram (FBD) of the bolt of the mechanical jack in the locked state shown in the figure.
The hand brake for a bicycle is shown. Portions DE and FG are free to rotate on bolt A which is screwed into the frame BC of the bicycle. The brake is actuated by a shielded cable where T1 is applied to point E and T2 is applied to point G. A spring having 40 N compressive force is placed between points E and G so that the brake stays open when it is not being used. Assume the change in the spring's force is negligible when the brake is actuated to produce the F = 100 N forces at points D and F. Determine the necessary cable forces T1 in N.
extension of spring when θ=90°. (m) angular velocity when θ=90° (rad/s)
A 1" diameter line shaft, which is supported by frictionless pulleys at the ends, carries 2 pulleys. The 10" diameter driver pulley is driven in a counter-clockwise direction, and its belt tensions are 25 lbs and 56 lbs. The 2" diameter driven pulley has one of its belt tensions measured at 30 lbs. Calculate the missing belt tension.
The coil springs of the vehicle_. a. support the weight of the vehicle b. provide axle location c. stabilize the up-and-down movement d. all of the above
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
What is the ratio L/R for which the uniform wire figure can be balanced in the position shown?
Two identical ball bearings Pand Qare operating at loads 30 kN and 45 kN respectively The ratio of the life of bearing P to the life of bearing Q is....
Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of gravity. Gear A has a radius of .8 ft and is experinceing a 10 ft-lb CW moment Gear B has a radius of 1.2 ft If gear A is initially moving at 60 rpm CW, determine how long it will take for gear B to be rotating at 300 rpm CCW