A single acting reciprocating pump has a bore of 15 cm and a stroke of 30 cm. The suction pipe has a diameter of 10 cm and is fitted with air vessel. Find the rate of flow into or from air vessel at 0 = 30° and 90°. Also find crank angle at which %3D there is no flow into or from air vessel. The pump runs at 120 rpm and the piston has S.H.M.

A single acting reciprocating pump has a bore of 15 cm and a stroke of 30 cm. The suction pipe has a diameter of 10 cm and is fitted with air vessel. Find the rate of flow into or from air vessel at 0 = 30° and 90°. Also find crank angle at which %3D there is no flow into or from air vessel. The pump runs at 120 rpm and the piston has S.H.M.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

Using the performance curve of pump A given in Example VIc.3.2 (41.5” and 710 rpm) and find: a) total dynamic head of a similar pump (pump B), at peak efficiency, having a diameter of 35 inches. Assume that both pumps A and B are operating at the same speed. b) pump head if pump B is now operating at 1170 rpm. [Ans.: a) H = 192 ft and b) H = 521.5 ft].
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
A single stage impulse turbine steam enters with a velocity of 420 m/s and runs at 3300 r.p.m. If the blade speed ratio is 0.44, then the diameter of the wheel in meter will be the diameter of the wheel in meter
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
A centrifugal pump discharges 96L/s while running at 1380rpm against a net head of 14m. The manometric efficiency of the pump is 0.92. If the vane angle at the outlet is 35 deg, estimate the outer diameter of the impeller and its width at that diameter. Assume the velocity of flow.
An inward flow reaction turbine, having an inner and outer diameter of 0.45m and 0.90m, respectively. The vanes are radial at inlet and the discharge is radial at outlet and the water enters the vanes at an angle of 12°. Assuming the velocity of flow as constant and equal to 2.8m/s, find the speed of the wheel and the vane angle at outlet. Show schematic diagram and provide solutions.
A pump has a suction condition of 50mm Hg vacuum pressure, 100mm diameter pipe and discharged condition of 250kpa at, 90mm diameter. The discharge tank is 50m elevation and the suction is 5m below the pump center line. If the discharge is 0.20 m3/s, find the pump efficiency for 260kw brake power. Answer: 74.32%
A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400 m. The nozzle diameter is 160 mm and the coefficient of velocity is 0.98, The diameter of the wheel bucket circle is 1.75 m and the buckets deflect the jet by 150°. The wheel-to-jet speed ratio is 0.45. Neglecting riction, calculate (1) the power developed by the turbine, (i) its speed and (i) hydraulic efficiency.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A. A water jet of diameter 180 mm impinges on the buckets of a Pelton turbine having overall efficiency of 85% while operating under a net head of 500 m and at speed of 420 rpm. Find the specific speed of the turbine. Take coefficient of velocity of the jet as 0.98 and speed ratio as 0.46. B. The pitch circle diameter of a Pelton wheel is 0.9 m. A jet of water of diameter 80 mm gets deflected by an angle of 170° when it impinges on the buckets. The bucket friction coefficient and coefficient of velocity of jet can be taken as 0.93 and 0.97 respectively. If the net head available on the wheel is 500 m and speed ratio is 0.45, calculate (a) the power transferred to to the wheel by the jet, (b) hydraulic efficiency, and (c) specific speed of the turbine. Take mechanical efficiency of wheel as 0.9.
EX.1 An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7 m?/minute running at 1500 rpm. The energy input is e ——T e T ‘a 125 J/kg and Total to Total efficiency is 0.75. If a geometrically similar pump has a diameter of 20 cm running at 3000 rpm, find its: i) Flow ratei) input power.
A centrifugal pump was designed for a 1940 rpm operation and a head of 63.4 m has a capacity of 201.2 l/s (lps) with a power of 135. kW. What effect will a speed reduction to 1200 rpm have on the head, capacity and power input of the pimp? What will be the changes in these variables if the impeller diameter is reduced from 332.5 mm to 275 mm while the speed is constant at 1800 rpm? Required a. For D = c, find Q2, H2 and P2 b. For N = c, find Q2, H2 and P2