A single loop RLC electrical circuit can be modelled as a second order system in terms of current. jÿ+3ÿ+9y=U(t) The natural frequency of the system in (rad/s) is The natural frequency of the system in (rad/s) is the damping ratio of the system 0.5 the settling time of the system is second is 2.66

A single loop RLC electrical circuit can be modelled as a second order system in terms of current. jÿ+3ÿ+9y=U(t) The natural frequency of the system in (rad/s) is The natural frequency of the system in (rad/s) is the damping ratio of the system 0.5 the settling time of the system is second is 2.66

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider two systems one is second order and the other is third order. The characteristic equations are: as2+bs+c for the second order and as3+bs2+cs+d for the third order, where a,b,c,d are positive real numbers. Then which of the following is correct with regard to the stability of these two systems? a. stability of either system cannot be confirmed with the given data b. third order is definitely stable but second order cannot be confirmed c. both systems are definitely stable d. second order is definitely stable but third order cannot be confirmed
A) Reduce the block diagram. B) G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 according to the given values, find the system's time constant, natural frequency, and damping rate, and explain what dynamic behavior it will exhibit accordingly. C) G1(s)= 2/s, G2(s)= 1/4s+2, G3(s)=4, H(s)=0.5 Find the poles and zeros of the system according to the given values. Accordingly, specify whether the system is stable. Find the unit digit response (reverse laplace)
For a single spine field, treated with 6MV (dmax = 1.5cm) to a depth of 5cm at 100cm SSD. What is the Mayneord F Factor for the following extended SSD setups?a. 110cmb. 120cmc. 130cmd. 140cme. 150cm
Which of the following is not true? a.Increasing system gain increases stability b.poles farther to the left of imaginary axisimprove speed c.steady-state errors are important in the studyof unstable systems d.multiple poles on the imaginary axis improvessystem stability
Electrical Engineering A cylindrical hollow pipe is made of steel (μr = 180 and σ = 4 x10^6 S/m).The external and internal radii are 7 mm and 5 mm. The length of the tube is 75 m.The total current I(t) flowing through the pipe is:I(t)= 8 cos(ωt) with ω=1200π rad/sDetermine:d) The intrinsic impedance of the good conductor. Remember that: Transcribed Image Text:η = = √2/45° σ·δ
The characteristic equation of a given system is s4 + s3 + 2s2 + 12s + 10 = 0. The stability condition of the system is __________. a. Stable b. Unstable c. Marginally Stable
The current i(t) in an RL circuit is governed by the differential equation di/dt + R/L i = 1/L (E(t)), where R and L are constants and E(t) represents the applied EMF. At t = 0, the switch in the circuit isclosed, and the applied EMF increases linearly from 0 V to 10 V in a time interval of 5 seconds. The EMF thenremainsconstantfort ≥5.Determinethecurrent in the circuit for t ≥0.
The characteristic equation of a control system is given below: F(s)= s4+s3+3s2+2s+5=0 The system is (A) Stable (B) Critically stable (C) Unstable
A resistor (R = 1 Ω), inductor (L = 0.1 H) and capacitor (C = 0.1 F) are connected in series, and the current I(t) through the circuit is measured as shown in the image below Assuming that the capacitor is uncharged at t = 0, and that the circuit is electrically small (such that propagation times between components can be neglected), find (or approximate where necessary) for times t = [0 : 0.1 : 0.4] (i.e. do not calculate at t = 0.5) : (shown in the image below)
The circuit components have values C1 = 5μF, C2 = 10μF, R1 = 2 Ω, R2 = 4 Ω, and R3 = 1Ω. Initially the battery is disconnected from the circuit. 1. The battery is connected to the circuit at t = 0 with both switches S1 and S2 initially open. What is the time constant of this RC circuit? What magnitude of the charge is on C1 five seconds after the battery is connected? 2. If S1 is, instead, initially closed when the battery is connected, discuss the qualitative behavior of the current flowing through R2 as a function of time (i) after a short time has passed since the battery was connected, and (ii) after a long time has passed since the battery was connected. (iii) How much energy is stored in C1 after a long time has passed? 3. Now consider the case where both switches are initially open and we connect the battery for a long time. We then disconnect the battery and then flip S2 closed. Find the current flowing through R3 as a function of time. What is the potential difference across…
G(s)=((s+1)*(s+15))/((s+0.1)*(s+2.5)*(s+120)*(s+240)) 1-draw nyquist 2- Nyquist criterion, compute the number of unstable poles of the closed loop system as a function of K 3-determine for which values of K the closed system is stable.
The structural engineering design section within the engineering department of a regional electrical utility corporation has developed several standard designs for a group of similar transmission line towers. The detailed design for each tower is based on one of the standard designs. A transmission line project involving 50 towers has been approved. The estimated number of engineering hours needed to accomplish the first detailed tower design is 126. Assuming a 95% learning curve, a. What is your estimate of the number of engineering hours needed to design the eighth tower and to design the last tower in the project? b. What is your estimate of the cumulative average hours required for the first five designs?