A single phase 120V AC sourc controls power to a resistve load 202 using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of ToN to produce 0.63kW power. d) The power factor for part (c). TON -TON

A single phase 120V AC sourc controls power to a resistve load 202 using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of ToN to produce 0.63kW power. d) The power factor for part (c). TON -TON

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

a) A sinewave is having a frequency of 50 Hz and instantaneous value of 200 Volts at 1.5 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.6 milli seconds.
Answer the question. 1. What is Alternating Current (AC)? Draw a simple graphical representation of AC. 2. What are the advantages of using alternating current over direct current?
2. A burst controlled triac is feeding a 200 ohm resistive load. The AC supply providing 240 V rms voltage at 60Hz. a) For one cylcle on, four cycles off control calculate the load rms voltage, current, power transferred to the load and efficiency. b) For four cylcles on, one cycle off control calculate the load rms voltage, current, power transferred to the load and efficiency.
A snubber circuit has snubber time constant (10 msec), voltage source (10 kV), discharge current of the Thyristor (5 µA) and frequency (50 Hz). Find the rate of voltage changing with time and snubber circuit power losses?
Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a) Exciting current (ii) Ic (b) Magnetizing Current (iii) Ie (c) core loss current
-p.m lap-wound dc series ge voltage 220 V and the pow
HOW TO Plot on the same graph two cycles of the primary current, the primary flux linkage, he primary input voltage, and the secondary induced voltage ON ANSYS?
a) A sinewave is having a frequency of 100 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and o =30 degrees. Vp t= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms b) Angular frequency =
Instantaneous voltage is multiplication of the resistace and .......... current in the resistive circuit. a) instantaneous b) average c) rms d) peak
3. A 120- volt AC voltage is applied across a 20- ohm resistive load. Find values of current, max voltage, peak – to - peak voltage, average voltage, maximum current, peak - to - peak current, average current and power.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
1) a) Describe and compare Direct Current (DC) and Alternating Current (AC).