A Single-Phase AC Distributor AB,400 meters long, is fed from end A and is loaded as under: A. 120 A at 0.6 pf lagging 300 m from Point A. B. 80 A at 0.45 pf lagging 400 m from Point A. The Resistance and Reactance of the Distributor is 0.4 Ω and 0.6 Ω per 500 m. Calculate the Total Voltage Drop in the Distributor. The Load Power Factors refer to the Voltage at the Far End

A Single-Phase AC Distributor AB,400 meters long, is fed from end A and is loaded as under: A. 120 A at 0.6 pf lagging 300 m from Point A. B. 80 A at 0.45 pf lagging 400 m from Point A. The Resistance and Reactance of the Distributor is 0.4 Ω and 0.6 Ω per 500 m. Calculate the Total Voltage Drop in the Distributor. The Load Power Factors refer to the Voltage at the Far End

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

A single phase AC distributor AB 500 m long is fed from end A and is loaded as under: (i) 70A at 0.707 p.f. leading150m from point A (ii) 30A at 0.8 p.f. lagging 500m from point A The load resistance and inductive reactance of the distributor is 0.3 Ω and 0.2 Ω per kilometer. If the voltage at the far end (B) is maintained at 230V, calculate the voltage at the sending end. The load power factor is referred to the voltage at the far end.
A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA power with 0.78 back power factor under 120 kV voltage is being shot. The conductor resistance value of the line is 0.10 Ω / km, the inductance value Since 1.30 mH / km and capacitance value is 0.001 µF / km, Medium Transmission Line establishing the equivalent circuit model; a) -Calculate the line current and voltage of the sending side. b) Calculate the power loss on the line. c) Calculate the% voltage regulation value of the line.
The resistance and reactance of the single-phase 60Hz transmission line conductors are 7.6 ohm and 6.6 ohm respectively. The transmission line delivers 20MW at a power factor of 0.66 lagging to the load with 54kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH b) Sending end power factor c) Percentage voltage regulation d) Percentage Efficiency
S.4) the length of a three-phase power transmission line with a Nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/km. From the end of the line, a 56 MW star connected load is fed with a power coefficient of 0.8 back under a 64 kV interphase voltage. If the line head voltage of the transmission line is 69 kV, calculate the capacity and power of the star-connected capacitor to be shunted into the load connected to the end of the line.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
A three-phase transmission line receiving end voltage is rated at 21 kV. A load of 1500 KW is connected at the receiving end of the transmission line 70 km long. The parameters of the transmission line are given by r = 0.09 Ω/km and x = 0.8 Ω/km. If the machine is working at 0.65 power factor lagging. Determine a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency
A single phase distributor 1 km long supplies a load of 100A at 0.8 p.f. lagging at its far end and a load of 200A at unity p.f. at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0.1 Ω and 0.2Ω respectively. If the voltage at the far end is maintained at 200V, calculate feeder current, voltage at the sending end . Also find phase angle between voltages at mid-point and sending end.
A single phase a. C distributor AB 300mts long if fed from end A is loaded as under a) 100amps at 0.707 p.f lagging 200mts from pointA(b) 200amps at 0.8p.f lagging 300mts from point A. The total resistance and the Reactance and the distributor is0. 2ohms and0. 1ohms per km respectively. Calculate the total voltage drop in the distributor. The load power factors refer to the voltage at the far end
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 10 and 10 A respectively and are fed from the cable at distance of 15 and 15 respectively. Calculate the voltage available across load 1 and 2
A circuit feeding a single-phase load of 2.75 kW at 0.85 power factor and 240 V at an ambient temperature of 55°C by means of a 27 m single-core PVC insulated cable run in conduit along with another circuit. 1) Determine the installation method 2) Compute the circuit design current (/g) 3) Determine the nominal current (Za) of the circuit breaker 4) Find the temperature correction factor (C;) and adjust current for temperature 5) Find the grouping correction factor (Cy) and adjust current for grouping of cables 6) Select cable size and determine its current carrying capacity (/z) 7) Check voltage drop (V.D.) and correct cable size if V.D. > 6 V
A 220 kV, 50 Hz, three-phase transmission line is 60 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.3 mH per km and the shunt capacitance is negligible. Use the short line model to determine; i) the voltage and power at the sending end ii) voltage regulation and efficiency when the line is supplying a three-phase load of 350 MVA, 220 kV at a power factor of 0.85 lagging.