A single-phase load is supplied by a single-phase voltage source. If the current flowing from the load to the source is 102– 150°A and if the voltage at the load terminal is 100Z 60°V, then the (A) load absorbs real power and delivers reactive power (B) load absorbs real power and absorbs reactive power (C) load delivers real power and delivers reactive power

A single-phase load is supplied by a single-phase voltage source. If the current flowing from the load to the source is 102– 150°A and if the voltage at the load terminal is 100Z 60°V, then the (A) load absorbs real power and delivers reactive power (B) load absorbs real power and absorbs reactive power (C) load delivers real power and delivers reactive power

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14P: A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance...

See similar textbooks

Similar questions

A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance Z=3.045, measured from the terminals. The source current is i(t)=22cos(t)kA. Determine the (a) instantaneous power, (b) real power, (c) reactive power delivered by the source, and (d) source power factor.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
Two three-phase generators supply a three-phase load through separate three-phase lines. The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4+j1.6) per phase between generator G1 and the load, and (0.8+j1) per phase between generator G2 and the load. If generator G1 supplies 15 kW at 0.8 poir factor lagging, with a terminal voltage of 460 V line-to-line, determine (a) the voltage at the load terminals. (b) the voltage at the terminals of generator G2, and (c) the real and reactive power supplied by generator G2. Assume balanced operation.
Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source. Load 1: Inductive load, 125kVA,0.28PF lagging. Load 2: Capacitive load, 10kW,40kvar. Load 3: Resistive load, 15kW. (a) Determine the total kW, kvar, kva, and supply power factor. (b) In order to improve the power factor to 0.8 lagging. a capacitor of negligible resistance is connected in parallel with the above loads. Find the kvar rating of that capacitor and the capacitance in F. Comment on the magnitude of the supply current after adding the capacitor.
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power
Two three-phase generating power stations, A and B, work at 97 kV and deliver power to their respective consumers as follows: Power station A delivers 900 MVA to its consumers at a power factor of 0.766 lagging. Power station B delivers 600 MVA to its consumers at a power factor of 0.819 lagging. An interconnector with an impedance of (1.5 + j5.6) Ω per line is connected between A and B. The voltage at power station A is advanced with an angle of 9° with respect to the voltage at power station B. Use the complex power method and do the following calculations. Determine the total active power delivered or received by Power station A (Pi) in MW Determine the total reactive power delivered or received by Power station A (Qi) in MVAr Determine the total active power delivered or received by Power station B (Pj) in MW. Determine the total reactive power delivered or received by Power station B (Qj) in MVAr Use complex power method to determine the final reactive power loadings (Qa) on…
A single phase system is supplying power at 220 V to an inductive and capacitive load of 30 A each, Inductive load is lagging the voltage by 30 degrees and capacitive load leading the voltage by 45 degrees. Compute the real and apparent power for both the loads (Question from subject introduction to power engineering)
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power