A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor laggin The total resistance of the line is 12 ohm and its total inductance is 90 mH. Determine a) sending-end voltage b) sending-end power factor c) percentage voltage regulation d) transmission efficiency

A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor laggin The total resistance of the line is 12 ohm and its total inductance is 90 mH. Determine a) sending-end voltage b) sending-end power factor c) percentage voltage regulation d) transmission efficiency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
A single phase overhead transmission line delivers 4000 kW at 11 kV at 0·8 p.f. lagging. If resistance and reactance per conductor are 0·15 Ω and 0·02 Ω respectively,Calculate:Percentage regulation sending end power factor Line losses
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
An 11 KV, 3-phase transmission line has a resistance of 1.5 Ω and reactance of 4 Ω per phase.Calculate the percentage regulation and efficiency of the line when a total load of 5000 KVA at 0.8 lagging power factor is applied at 11KV at the distant end.
A 69-kV, three phase short transmission line is 16km long. The line has a per phase series impedance of 0.125 + j0.4375 ohms per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers:(a) 70 MVA, 0.8 lagging power factor at 64 kV.(b) 120 MW, unity power factor at 64kV.
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
For Figure 1: A short 3-phase line with an impedance of (6+j8) per line has sending end and receiving end line voltages of 120 and 110 kV, respectively. If the power factor at this loading is 0.90 lagging, determine (a) the current delivered to the load, (b) the power consumed by the balanced 3-phase load in kW, and (c) the voltage regulation of the system. (hint: Voltage at the sending and receiving have some magnitude but different angles.)